美国ARS EPR,ESR专用液氦型低温恒温器 LTR

Model RO-600(1K) – Ruthenium Oxide RTD – RuO Thermometer from Scientific Instruments

The Model RO-600 Ruthenium Oxide Temperature Sensors are thick film resistors which adhere to are available with calibration down to 20mK or grouped/interchangeable and have a nominal resistance of 1,000? at ambient temperature. The ruthenium oxide temperature sensor offers excellent performance characteristics in magnetic field environments. These sensors exhibit an initial small negative magnetoresistance at temperatures below 250 mK at low fields (less than about 1.5 Tesla). The magnetoresistance then becomes positive at larger fields and increases at lower temperatures. This magnetoresistance is repeatable. For example, a resistance change of 8% induced by an 8 Tesla field at a temperature of 80 mK corresponds to a temperature error of 7 mK.

Model SI-435 Silicon Diode Temperature Sensors

Si-435 Silicon Diodes from Scientific Instruments offer the industry’s highest 4K accuracy in an interchangeable/uncalibrated diode temperature sensor. The CAP package is the smallest encapsulated diode mount on the market while the SMD package offers the utility of a compact surface mount. Individually calibrated options are available where millikelvin accuracy is required.

VIS-Datasheet-V25-850M-module

High-speed transmitter module for test purpose with integrated 850nm VCSEL fiber coupled to an OM3 multimode fiber for optical output. The module is designed as engineering sample for high speed test applications. Multi mode and single mode VCSEL versions are available.

VIS-Datasheet-D30-850M

These high speed photodetector modules consist of a GaAs pin photodetector integrated with a 50 µm-core diameter multimode fiber for optical input. The responsivity is greater than 0.4 A/W at 850 nm. The modules are engineering samples and use an optional external DC bias

VIS-Datasheet-A56-230C_v1-1

The A56-230 is a high speed VCSEL driver IC designed for directly modulated VCSELs in fiber optic transmission systems. The VCSEL driver IC is designed to directly modulate common-cathode VCSEL. The IC has differential input (Vin+, Vin-) and single-ended output to the VCSEL anode. A ground for the VCSEL common cathode is also provided by the IC. It is operated with a single 3.3 V supply typically dissipating less than 200 mW of DC power when no load (VCSEL) is connected at the output. The driver is also equipped with various analog control pins (Vxing, Vmod, Vbias). The zero-crossing can be adjusted with the Vxing pin. The VCSEL modulation current is controlled by varying the bias current swing with the Vmod, and the VCSEL bias current is controlled by Vbias pin.

VIS-Datasheet-A56-230C_v1

The A56-230 is a high speed VCSEL driver IC designed for directly modulated VCSELs in fiber optic transmission systems. The VCSEL driver IC is designed to directly modulate common-cathode VCSEL. The IC has differential input (Vin+, Vin-) and single-ended output to the VCSEL anode. A ground for the VCSEL common cathode is also provided by the IC. It is operated with a single 3.3 V supply typically dissipating less than 200 mW of DC power when no load (VCSEL) is connected at the output. The driver is also equipped with various analog control pins (Vxing, Vmod, Vbias). The zero-crossing can be adjusted with the Vxing pin. The VCSEL modulation current is controlled by varying the bias current swing with the Vmod, and the VCSEL bias current is controlled by Vbias pin.

VIS-Datasheet-A56-105C

The A56-105 is a high speed VCSEL driver IC designed for directly modulated VCSELs in fiber optic transmission systems. The VCSEL driver IC is designed to directly modulate common-cathode VCSEL. The IC has differential input (Vin+, Vin-) and single-ended output to the VCSEL anode. A ground for the VCSEL common cathode is also provided by the IC. It is operated with a single 3.3 V supply typically dissipating less than 105 mW of DC power when no load (VCSEL) is connected at the output. The driver is also equipped with various analog control pins (Vxing, Vmod, Vbias). The zero-crossing can be adjusted with the Vxing pin. The VCSEL modulation current is controlled by varying the bias current swing with the Vmod, and the VCSEL bias current is controlled by Vbias pin.

Model SD-6-15 Storage Dewar Magnet System

Model SD-6-15 Storage Dewar Magnet System • 6 Tesla magnet with vertical access • Low-loss liquid helium storage dewar • 4K sample insert

Model 430 Power Supply Programmer

The AMI Model 430 Power Supply Programmer is a sophisticated digital power supply controller that allows an operator to manage a superconducting magnet system with unprecedented accuracy and ease. The Model 430 is designed to control a wide range of single, dual, and fourquadrant linear and switching power supplies. The most frequently used functions are accessible via single keystroke or shift plus keystroke. For other functions, a menu driven format guides the user to enter inputs using the push button front panel interface.

MAxes_Information_Brief

Multi-Axis Magnet systems for Vector Fields (MAxesTM)

STT - shaft twist tester Flyer English

STT – Shaft Twist Tester Production-related optical twist testing on radial shaft sealings To avoid leakage on radial shaft sealings the sealing surface has to be manufactured without twist. Optical diffraction analysis can visualize twist structures with amplitudes far below the amplitude of the surface roughness. Applying this method, the quality control can be realized quickly and reliable within the production process. Testing times of a few seconds are making the device applicable in many cases, for example at the reception control, for optimization of the manufacturing process and even for the 100%-control in the serial production.

magview Flyer English

The magview is a magneto-optical device for the fast and accurate visualization of magnetic structures. As a handheld device, the system can be applied for qualitative tests and stray field analyses. The magview visualizes magnetic stray fields, for instance of magnetic stripe cards, magnetic encoders and multi pole magnets.

mageye Flyer English

The mageye is a digital microscope camera system with an integrated magneto-optical sensor tip for the fast and reliable visualization of magnetic stray field structures. The portable system, including a comprehensive user software allows realtime stray field analyses and quality tests of magnetic materials. It is possible to visualize magnetic stray fields of magnetic stripe cards, magnetic tapes, magnetic encoders, obliterated serial numbers, magnetic ink as well as di- and multipole magnets.

3MTS Flyer English

3MTS is the USB handheld Teslameter developed in cooperation with Matesys’ partner company SENIS AG.

ThermoelectricEffect热电效应

热电效应是热和电之间的关系。当器件的两侧产生温差时，材料中的载流子从热的一端扩散到冷的一端，从而在期间上产生电压。相反，当施加电压时，热量从一端传递到另一端，行程温度梯度。热电效应一般由塞贝克Seebeck 效应、佩尔蒂埃Peltier 效应和托马森Thomason 效应三种效应组成。

ElectronParamagneticResonance(EPR)ElectronSpinResonance(ESR)

Electron paramagnetic resonance (EPR)/electron spin resonance (ESR) is an important method to study unpaired electrons in organic and inorganic radicals, transition metal complexes, and some biomolecules.When paramagnetic compounds with unpaired electron spins are under magnetic fields and electromagnetic waves, normally in the microwave range of frequency, the transition between spin states is induced. The measurement is generally carried out with constant frequency, while the magnetic field varies. EPR/ESR spectrometer measures the absorption of electromagnetic radiation. Due to the short relaxation times of electron spins, EPR/ESR must be performed at cryogenic temperatures.

ElectronParamagneticResonance(EPR)ElectronSpinResonance(ESR)电子顺磁共振电子自旋共振

电子顺磁共振(EPR)/电子自旋共振(ESR)是研究有机和无机自由基、过渡金属配合物和一些生物分子中未配对电子的重要方法。当具有不成对电子自旋的顺磁性化合物在磁场和电磁波(通常在微波频率范围内)作用下，就会诱导自旋态之间的跃迁。测量一般是在恒定频率下进行，而磁场是变化的。EPR/ESR 光谱仪测量电磁辐射的吸收。 由于电子自旋的弛豫时间短，EPR/ESR 必须在低温下进行。

Linear Rotary Feedthroughs

Precision Linear Feedthroughs — Welded bellows shaft seal with 1, 2 and 4 Inch linear travel lengths. Precision Rotary Feedthroughs — Welded bellows shaft seal with 360° plus, continuous rotational travel. Economy Rotary Feedthroughs — Elastomer shaft seal with 360° continuous manual rotational travel. Actuator Options — DC Stepper, AC motorized, and pneumatic actuator options available.

LTR

LTR专为X波段EPR和ESR测量而设计。 通过石英比色皿内的液氦射流冷却样品。 我们提供符合Bruker、Varian和JEOL腔体的玻璃器皿。

我司在北京师范大学顺利完成美国ARS公司LT3液氦液氮型低温恒温器验收工作

近日我司在北京师范大学顺利完成美国ARS 公司（ADVANCED RESEARCH SYSTEMS）LT3 液氦/液氮型低温恒温器验收工作，搭配布鲁克Bruker VERTEX 80V 光谱仪；该款恒温器采用同轴液氦冷却低温传输管线，液氦消耗率同类产品最低0.7LL/hr@4.2K.降温时间只有20 分钟。

我司在中国科学院合肥物质科学研究院顺利完成美国ARS超低振动超紧凑型低温恒温器验收工作

近日我司在中国科学院合肥物质科学研究院顺利完成美国ARS（ADVANCED RESEARCH SYSTEMS）超低振动超紧凑型低温恒温器验收工作，该款超低振动低温恒温器为完全无液氦系统，超级紧凑的尾端结构只有19mm, 可实现电磁铁的最大磁场，特制的三维支架可实现样品的三维精密移动，是显微磁光测试的首选。

X-4大样品腔闭循环低温恒温器

X-4大样品腔闭循环恒温器拥有不锈钢结构和仪表群，并有更大的样品空间，可放置金刚石压砧或其他大体积样品。标准的真空罩有4个窗口位置，底部可加第五个窗口位置。 X-4系列恒温器可配备DE-202或DE-204系列冷头，根据客户需要可选择4K，5.5K，10K不同型号。

ds.cc210

Unique Features: • Cooling power on first stage is higher than comparable systems for cooling larger radiation and other parasitic heat loads for magnet cooling. • Pneumatic Drive Displex Cryocooler for low vibrations at the sample (see Specifications). • Only two moving/Wearing components for high reliability. • Displacer can be removed from the cryocooler for maintainence in the field without breaking vacuum. • Tunable for high performance at any heat load. • Easy field maintenance. Low life cycle cost. • Compressor Model ARS-10HW is water cooled for quiet and clean operation. • Low cooling water flow rate.

DS-CS210AF-GMX-20B

The CS210*F-GMX-20B opens up a wide range of possibilities never before possible with a closed cycle cryocooler. The ARS manufactured DMX-20B interface, like our “B” series cold heads is a True UHV System (10-11 Torr) where all of the rubber o-ring seals have been replaced with welded joings and metal seals. A CF flange is The DE210*F-GMX-20B uses a Helium Exchange Gas to decouple the sample from the cold tip of the DE210 Cryocooler. This prevents almost all vibration from being transmitted to the sample. Due to the exchange gas being less conductive, the base temperature will increase by ~1K and the cooling capacity is roughly cut in half at varying temperatures.

µDriftSystemFlier

The ARS μDrift Cryostat is purpose built to remove key barriers to long-term optical and variable temperature experiments. Combining the company’s experience in robust cryogenics with convenient optical access and new low drift designs assures success when studying nanometer scale samples and other structures.

DS-LT3B

The ARS manufactured LT3B Helitran is a True UHV cold head (10-11 Torr) where all of the rubber o-ring seals have been replaced with welded joints and metal seals. Like all of our LT3 helium flow cryostats, the LT3B is an advanced liquid helium flow cryostat utilizing many unique features, such as the matrix heat exchanged and the coaxial shield flow transfer line to achieve unparalleled efficiency and ultra low vibration levels. The combination of True UHV and angstrom level vibrations makes the LT3B ideal for low temperature STM application. For UHV surface science where very long cold fingers are required we have the LT3M with customizable length up to 1200 mm and rigid support tube to allow for cleaving and manipulation.

BRAIDCABLES

High-quality custom braids, cables and strands call for a high degree of technical expertise, precision manufacturing equipment, and short lead times—all core strengths of New England Wire Technologies. We’ve earned a solid reputation for our ability to turnaround both large and small orders in record time. And many of our braids, cables and strands are in stock and ready to ship.

美国GMW-hw-108a_gmw

Please be aware that our products are not intended for use in life support equipment, devices, or systems. Use of our products in such applications requires the advance written approval of our sales staff.Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks,adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of our products in such applications is understood to be fully at the risk of the customer using our devices or systems.

美国GMW-hw-101a-4t_gmw

Please be aware that our products are not intended for use in life support equipment, devices, or systems. Use of our products in such applications requires the advance written approval of our sales staff. Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks,adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of our products in such applications is understood to be fully at the risk of the customer using our devices or systems.

美国GMW-hq-8220_gmw

•Please be aware that our products are not intended for use in life support equipment, devices, or systems. Use of our products in such applications requires the advance written approval of our sales staff. Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks,adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of our products in such applications is understood to be fully at the risk of the customer using our devices or systems. •Handling precautions required for preventing electrostatic discharge. •This product contains galium arsenide（GaAs）.Handling and discarding precautions required.

美国GMW-hq-0221_gmw

•Please be aware that our products are not intended for use in life support equipment, devices, or systems. Use of our products in such applications requires the advance written approval of our sales staff. Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks, adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of our products in such applications is understood to be fully at the risk of the customer using our devices or systems. •Handling precautions required for preventing electrostatic discharge. •This product contains galium arsenide（GaAs）.Handling and discarding precautions required.

美国GMW-hg-0814_e

•Please be aware that our products are not intended for use in life support equipment, devices, or systems. Use of our products in such applications requires the advance written approval of our sales staff. Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks,adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of our products in such applications is understood to be fully at the risk of the customer using our devices or systems. •Handling precautions required for preventing electrostatic discharge. •This product contains galium arsenide（GaAs）.Handling and discarding precautions required.

美国GMW-hg-176a_e

•Please be aware that AKE products are not intended for use in life support equipment, devices, or systems. Use of AKE products in such applications requires the advance written approval of the appropriate AKE officer. Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks,adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of AKE products in such applications is understood to be fully at the risk of the customer using AKE devices or systems. •Handling precautions required for preventing electrostatic discharge. •This product contains galium arsenide（GaAs）.Handling and discarding precautions required.

美国GMW-hg-166a-2u_gmw

•Please be aware that AKE products are not intended for use in life support equipment, devices, or systems. Use of AKE products in such applications requires the advance written approval of the appropriate AKE officer.Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks,adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of AKE products in such applications is understood to be fully at the risk of the customer using AKE devices or systems. •Handling precautions required for preventing electrostatic discharge. •This product contains galium arsenide（GaAs）.Handling and discarding precautions required.

美国GMW-hg-106c-2u_gmw

Please be aware that AKE products are not intended for use in life support equipment, devices, or systems. Use of AKE products in such applications requires the advance written approval of the appropriate AKE officer. Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks, adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of AKE products in such applications is understood to be fully at the risk of the customer using AKE devices or systems.

美国GMW-G-0714

Shipped in packet-tape reel(10,000pcs per reel) Notice : It is requested to read and accept "IMPORTANT NOTICE" written on the back of the front cover of this catalogue.

Zero-Gauss-chamber-ZG7

To obtain a null field reference a Zero Gauss chamber must be used to shield the probe sensing area from external field. The ZG7 is particularly designed accessory for the SENIS Magnetic Mapping Systems.

XT-High-field-Dipole-Analysis-Magnets-Brochure

• Continuously variable field • Cryogen-free • Fast cooldown • Compact design • Low fringe field • Option to vary orientation of magnet mount

Wada-FCT

For any experiments that use beams of an accelerator,monitoring the beam intensity is always an important concern. It is particularly useful if one can continuously measure the beam current without disturbing the beams. Counting elastic scattering particle from the target is often used for such a purpose,however, the dynamic range of measurable beam intensity is limited and the calibration often changes for different experimental conditions.

VWM-S-1W-A60mm-TopView

VWM-S-1W-A60mm-TopView VWM-S-1W-A60mm-TopView VWM-S-1W-A60mm-TopView

VWM-S-1W-A40mm-TopView

VWM-S-1W-A40mm-TopView VWM-S-1W-A40mm-TopView VWM-S-1W-A40mm-TopView

VWM-S-1W-A20mm-TopView

VWM-S-1W-A20mm-TopView VWM-S-1W-A20mm-TopView VWM-S-1W-A20mm-TopView

VWM-S-1W-A5mm-TopView

VWM-S-1W-A5mm-TopView VWM-S-1W-A5mm-TopView VWM-S-1W-A5mm-TopView

VWM-S-1W-A5mm-FrontView

VWM-S-1W-A5mm-FrontView VWM-S-1W-A5mm-FrontView VWM-S-1W-A5mm-FrontView

US-Danisense-Product-Naming-Price-List-2018-letter

Since our establishment in November 2012, Danisense’s philosophy has always been to provide you the best in everything we do. In return, the market feedback has been so good. Our growth has constantly exceeded expectation. In the past several years, we’ve continuously released new products to broaden our offering.

TN-IPCT

IPCT performance recovery after primary current overload

TNG3DTM005a

The Group3 Teslameter (serial versions) may be connected to a host computer using fiber optic cables. This has the advantage of electrically isolating the DTM and is particularly advantageous when using the DTM in electrically noisy or high voltage environments.

TNG3DTM001a

Caution: The software EPROMs may be damaged by static discharge. Use proper handling procedures to reduce the risk of damage. Items damaged by static discharge are not covered under warranty.

THM1176-LabviewRTE-Error

Why am I getting this error: “Unable to locate LabVIEW Runtime” ? This error typically is caused by the LabVIEW runtime engine and VISA runtime engine not installed or not correct version installed. When you saw the error there should have mention what version of runtime engine was missing.

Thermo_Fisher_Chiller_1490G-CIRC_Manual

Thermo Scientific ThermoFlexTM Recirculating Chillers (Deluxe Controller)

The-Parametric-Current-Transformer-A-Beam-Current-Monitor-Developed-for-LEP

Toroidal transformers are used to measure the beam current in beam lines and accelerators. Placing such a transformer hi the feedback loop of an operational amplifier will increase the useful frequency range (active current transformer). A magnetic modulator can be added to extend the response to DC current, maintaining with a control loop the transformer core at a zero flux state.

Tech-Note-Current-Transducer-Cable

Tech Note: Current Transducers “Wrap Around” or Distributed Primary Current Cable

SV

Rundsteckverbinder mit Schraubverschluss nach IEC 60130-9, IP 40 Circular connectors with threaded joint acc. to IEC 60130-9, IP 40 Connecteurs circulaires avec verrouillage à vis suivant CEI 60130-9, IP 40

stulle_inpac2018

The CWCT is a novel instrument developed for the accurate determination of the CW beam average current. It measures average beam currents down to the microampere level with noise contributions below 1 μA. Its output signal follows beam current fluctuations within ≤1 μs, permitting fast detection of beam loss. These characteristics render the CWCT an ideal instrument for proton and ion accelerators. We present the CWCT principle and laboratory measurements using various input signals.

SN-mft-model-numbering-guide

A SENIS Magnetic Field Transducer (a magnetic flux density-to-analog voltage transducer, hereinafter MFT) consists of two modules: 1. The Hall probe module H (including the cable CaH) and 2. The Electronic module E.

SN-DS-hall-probe-g-for-i1a-mft

Hall Probe G for F1A Magnetic Transducers with the naked Si chip is a very thin (0.5mm) and long (42mm) single-chip integrated 1-axis Hall-Probe. It measures magnetic fields perpendicular to the probe plane (By).

Shape-B-SMA

CURRENT TRANSFORMER- SHAPE B/SMA CONNECTOR CURRENT TRANSFORMER- SHAPE B/SMA CONNECTOR

SENIS-CS_Spec

The SENIS CS series current sensors offer low current sensing with high voltage isolation capability. The SENIS CS sensor incorporates the Melexis MLX91206 high sensitivity Hall IC and a multi-turn coil to further increase sensitivity.

s-bpmdatasheet

Non-interceptive beam position measurement For linacs, microtrons and transfer lines Single bunch, macropulse and CW Beam charge range > 1000

RD102-EM3242

The RD102-EM3242 is a reference design for the AKM EM-3242 Non-Contact Angle Position Sensing IC. The EM-3242 senses the angle of magnetic field component in the top plane of the device package. The EM-3242 provides an analog output voltage of 10% to 90% of the supply voltage for a mechanical angle range of 360 degrees of rotation. The EM-3242 has two operating modes. One with the “In Range” detector enabled and one with the “In Range” detector disabled. The “In Range” detector includes internal circuitry which causes the output voltage to drop to 0V whenever the magnetic field level at the EM-3242 is greater than 60mT or less than 10mT.

RCT1A-Dimensions

RCT1A-Dimensions RCT1A-Dimensions RCT1A-Dimensions

PSU1-OM2443

Operation Manual for PSU1 Power Supply Unit Operation Manual for PSU1 Power Supply Unit

Principle-of-Zero-Flux-CTs

The primary current, ??, in a conductor through a magnetic core will generate a magnetic flux in the core ????.

PPM-DS-p2p-ACLink

The AC point2point link is capable of transmitting analogue signals of up to 3GHz over singlemode fibre. The capability to transmit any type of low level RF signal within this pass band makes it ideal for EMC measurements, HPM experiments or distributed timing. The modules are available in a fully EM shielded casings, or as a plug-in module for use with the various point2point housings.

PPM-DS-FOCable

From patch-leads through to cross-site cables, or optical adapters through to patch panels, PPM’s one-stopshop approach to fibre optic cable management offers a range of various high performance solutions designed to facilitate the quick and easy installation of all its fibre optic link products.

PPM-73461-HB-2-NiMH-battery-Handbook

Nickel Metal Hydride Battery Pack773461-HB-2 User Handbook

PA1-Power-Amplifier-OM3225

Operation Manual for PA1 Power Amplifier Operation Manual for PA1 Power Amplifier

PA1-DR3047

PA1 Power Amplifier Outline Drawing PA1 Power Amplifier Outline Drawing

Output-signal-cable-COxx-G

Output Signals Cable COxx-G Output Signals Cable COxx-G

Output-signal-cable-CO50

Output signal cable CO50 Output signal cable CO50 Output signal cable CO50

NPCT-RFC

NPCT-RFC NPCT-RFC NPCT-RFC NPCT-RFC NPCT-RFC NPCT-RFC

NPCT-manual

New Parametric Current Transformer User’s Manual New Parametric Current Transformer User’s Manual

NPCT-CF6-96-120-w

NPCT-CF6"-96.0-120/1.0 NPCT-CF6"-96.0-120/1.0 NPCT-CF6"-96.0-120/1.0

NPCT-175

NPCT-175 NPCT-175 NPCT-175 NPCT-175 NPCT-175 NPCT-175

NPCT-75-H

NPCT-75-H NPCT-75-H NPCT-75-H NPCT-75-H NPCT-75-H NPCT-75-H

MX-BPM_101_gain_adjust

The gains can be adjusted over a wide range by changing a few components: Xgain is determined by the equivalent resistance of R177 in parallel with R176. Ygain is determined by the equivalent resistance of R161 in parallel with R162

MS3-USB-Cable-DR2373

MS3 USB Cable Assembly MS3 USB Cable Assembly MS3 USB Cable Assembly

MS3-RS232-Cable-DR2517

MS3-RS232-Cable-DR2517 MS3-RS232-Cable-DR2517 MS3-RS232-Cable-DR2517

MS3-DR3417

MS3 Outline Drawing MS3 Outline Drawing MS3 Outline Drawing

MS2-MS2WFP-RS232-Cable-DR1042

MS2-MSWFP CABLE RS232 2M ASSEMBLY MS2-MSWFP CABLE RS232 2M ASSEMBLY

MS2K-DR1830

MS2K-DR1830 MS2K-DR1830 MS2K-DR1830 MS2K-DR1830 MS2K-DR1830

MS2_MS3-DS0020

MS2/MS3 Magnetic Susceptibility System MS2/MS3 Magnetic Susceptibility System

Model_5201_mapa_data

Model 5201 Projected Field Electromagnet Field Map Data

MMS-1A-RS-Standard-Samples-and-Maps

MMS-1A-RS is the high-end version of the SENIS 3-axis Magnetic Field Mapping System that allows users to perform a fast, high resolution mapping of magnetic field around permanent magnets, electromagnets and electronic circuit PCBs. The map of the magnetic field can be presented as color coded 1D, 2D or 3D isometric visual displays and as a table of numerical values of the magnetic field and the geometrical coordinates of measured points. The measured data analysis is performed during the mapping of the magnetic field, so that calculated data required for the analysis can be visualized immediately after the mapping.

MLVMCTRL-GMW-Magnet-Control-Software-manual

USER’S MANUAL MODEL: LVMCTRLLABVIEW MAGNET CONTROL

ML_TN_THM1176-HF-as-a-Thermometer

In order to compensate for temperature drift, the THM1176-HF sensor includes a temperature sensor. The THM1176 command set allows reading its value. Does this mean that I can use the THM1176 as a thermometer?

ML_DS_pt2025

An everyday tool for rapid, automatic and highly accurate measurements of magnetic fields: research, magnet manufacturing and testing, standards and calibration.

MFC2046-Installation-and-Safety-Manual

Magnetic Field Camera MFC2046 Version 1.0 (Revision 1.2) December 2018 EN Installation and Safety Manual FR Manuel d'installation et de sécurité

Matesy-MAN-MagView

DELIVERY CONTENTS • MagView and transport-case • Power supply unit (Input: 230 VAC, Output: 5.0 VDC), storage battery • User manual

Matesy-MAN-MagEye

Matesy-DS-MagEye Matesy-DS-MagEye User Manual MagEye

Matesy-DS-MiniMo

Being a small and light testing device, Minimo can be used as a stationary and mobile system for fast visualization of magnetic stray fields. The webcam-based Minimo is applicable for a qualitative examination of magnetic stripe cards, removed serial numbers and hard magnetic material structures. In addition to plug-and-play ability and image archiving a simple change of the magneto-optical sensor head is possible. Minimo can be equipped with all types of magneto-optical sensors. This allows an adaption of the Minimo to the sample field strength.

Magnetics2016-SENIS-Presentation

Integrating Magnetic Field Mapping Crack Detection and Coordinate Measurement Author: S. Spasic, Senis AGPresented by: Ben Hartzell, GMW Associates

Mag690-OM2604

Operation Manual for Mag690 Three-Axis Fluxgate Magnetometer

Mag690-DR2687

Mag690-DR2687 Mag690 Outline Drawing Mag690 Outline Drawing

ew-402_gmw

EW-402 is composed of a Ultra-high sensitive InSb Hall element and a signal processing IC chip in a package.

ew-400_gmw

EW-400 is composed of a Ultra-high sensitive InSb Hall element and a signal processing IC chip in a package.

EQ-732L_MS-1380-E-00_120508-gmw

• Analog output voltage proportional to the magnetic flux density • Magnetic sensitivity 40mV/mT (typ.) • Supply voltage from 3.0V to 5.5V at single power supply • Operating temperature range from -40°C to 100°C • Ratio-metric analog output • 3pin single in-line package (SIP), Halogen free • Quick response 1μs (typ.) • Low output noise voltage 3mVp-p

eq-433l_e

EQ-433L is composed of an InAs Quantum Well Hall Element and a signal processing IC chip in a package Notice:It is requested to read and accept "IMPORTANT NOTICE" written on the back of the front cover of this catalogue.

em-1781_gmw

EM-1781 is ultra-small Hall effect ICs of a single silicon chip composed of Hall element and a signal processing IC.

em-1011_gmw

EM-1011 is ultra-small Hall effect ICs of a single silicon chip composed of Hall element and a signal processing IC.

DTM-132-Manual

Complete 4-channel system interface unit for ultra-stable, high precision fluxgate tech-nology DS series current transducers.

DSSIU-4-1U

Complete 4-channel system interface unit for ultra-stable, high precision fluxgate tech-nology DS series current transducers. Powers up to 4 x DS50 to DS2000 at the same time.

DS-HTS-110-LM

Applications HTS-110’s LM range is suitable for various applications, including: 4 MOKE (Magneto-optic Kerr effect) 4 Magnetic domain imaging 4 Brillouin light scattering 4 Magnetic circular dichroism 4 Hysteresis loop plotting 4 Scanning laser microscopy 4 Hall effect measurements 4 Variable temperature optical cryostat

DS-DS-DSSIU-4-1U

Complete 4-channel system interface unit for ultra-stable, high precision fluxgate tech-nology DS series current transducers.

DS5000UBFS-10V7500A

Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 8000A

DS600UB-10V

Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 660A

DS600ID-CD100

Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 1000A

DS600ID

Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 1000A

DS200UB-10V

Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 220A

DR1395

DR1395 MS2 magnetic susceptibility meter MS2 magnetic susceptibility meter

DR0756

DQ640ID-B is a current transducer targeting stable power supplies and other areas, where it is important to have the programming flexibility

DR0656

DQ640ID-B is a current transducer targeting stable power supplies and other areas, where it is important to have the programming flexibility

DM1200ID

Ultra-stable, high precision (ppm class) fluxgate technology DM Series current transducer for non-intrusive, isolated DC and AC current measurement up to 1500A

DL2000UB-1V

Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 3000A

Datasheet_DC200IF

Highly stabilized and precise fluxgate technology based current transducer, re-engineered for cost sensitive, non-intrusive, isolated DC and AC current measurement applications up to 300A

Danisense-Product-Name-Guide

Danisense-Product-Name-Guide PRODUCT NAMING RULES

CZ-3706

CZ-3706 is an open-type current sensor using Hall sensors, which outputs the analog voltage proportional to the AC/DC current. Group III-V semiconductor thin film is used as the Hall sensor, which enables the high-accuracy and high-speed current sensing. Coreless ultra-small surface mount package realizes the space-saving.

CWT-Ultra-mini

The CWT Ultra-mini has an extremely thin, clip-around Rogowski coil of typically 1.6mm cross-section. Such a thin coil enables currents to be measured in the most difficult to reach parts of a power electronic converter with negligible disruption to the circuit under test.

CWT_UM-instructions

ROGOWSKI CURRENT WAVEFORM TRANSDUCERS INSTRUCTIONS FOR USE CWT ULTRA MINI

CWT_MINI-instructions

PEM’s Rogowski Current Waveform Transducers combine high bandwidth, safety, and the minimum disruption to the circuit under test. These instructions should be followed whenever the unit is used. They are intended to help you obtain the best and safest performance from the transducer.

cwt_mini

Instructions for CWT Integrator Module Fuse Replacement

cwctmanual

CWCT & BCM-CW-E CW Current Transformer Beam Charge Monitor for CW beams and Macropulses User’s Manual

CU1-Control-Unit-OM3224

Operation Manual for CU1 Helmholtz Coil System Control Unit

CT-07.08.App_.note

Bergoz Instrumentation Current Transformers have been employed in an interesting application to detect faults in the electricity supply lines in Southern Africa. ABB successfully installed Bergoz CTs recently and the system described below is now operational in the field.

CS_Series_PAD

CQ-3303 is an open-type current sensor using a Hall sensor which outputs the analog voltage proportional to the AC/DC current. Quantum well ultra- thin film InAs (Indium Arsenide) is used as the Hall sensor, which enables the high-accuracy and high-speed current sensing. Coreless surface mount package realizes the spacesaving.

CQ-2235

CQ-2235 is an open-type current sensor using a Hall sensor which outputs the analog voltage proportional to the AC/DC current. Quantum well ultra-thin film InAs (Indium Arsenide) is used as the Hall sensor, which enables the high-accuracy and high-speed current sensing. Simple AI-Shell package with the Hall sensor, magnetic core, and primary conductor realizes the space-saving and high reliability.

CQ-2234

CQ-2234 is an open-type current sensor using a Hall sensor which outputs the analog voltage proportional to the AC/DC current. Quantum well ultra-thin film InAs (Indium Arsenide) is used as the Hall sensor, which enables the high-accuracy and high-speed current sensing. Simple AI-Shell package with the Hall sensor, magnetic core, and primary conductor realizes the space-saving and high reliability.

CQ320B

CQ320B CQ320B CQ320B CQ320B CQ320B CQ320B CQ320B CQ320B

CMC

PEM has developed a flexible, clip-around, current probe to measure high frequency common mode currents which flow around a motor drive to ground via the bearings in large AC drive systems.

CATALOG_AKM-Kit-and-Ref-Catalog

AKM Magnetic Sensors Engineering Development Kits Demonstration Modules Application Case Studies

Brochure-PT2026-1.1-US

The world’s most precise magnetometer Metrolab’s PT2026 sets new standards for magnetometers based on NMR (Nuclear Magnetic Resonance), the most precise technique for measuring magnetic flux density. The combination of a pulsed-wave NMR detector and advanced signal processing opens a host of new applications in the areas of magnetic field measurement, monitoring, mapping and calibration.

BPM-AFE.11flyer

BPM-AFE is an analog frontend to process RF signals from beam position pickup electrodes. It delivers an output signal which can be directly entered into fast 14-bit ADCs. It is specially developed for transfer lines and linacs. It can be customized to any RF frequency up to 1 GHz.

BBM-Schematic

The Ametes Bus Bar DC Current Sensor locates two magnetic field sensors on each side of an electric current bus bar. Two Sentron CSA-1VG precision Hall Effect IC sense the magnetic field as a function of current on both sides of the bus bar. This enables effective cancellation of external magnetic fields without magnetic cores or shielding which can give rise to non-linearity and hysteresis effects.

Bartsoft-PC-OM2647

Bartsoft software acquires, corrects, displays, stores and prints data using Bartington Instruments MS2 and MS3 meters. This guide explains how to use the software and helps the user understand how it works, including the function of all controls and windows.

Bartington-Export-Control

Bartington Instruments manufactures a range of Fluxgate magnetometers and acquisition units, magnetic susceptibility systems, and a range of test equipment. Some of these products are subject to export control. The summary below is provided to give an overview of the rules that apply.

app-note-cryosaver

CryoSaver current leads employ HTS tape which has anisotropic in-field performance. The current rating decreases much more severely for field oriented perpendicular to the plane of the tape than for field parallel to the plane (either along the long axis or across the width of the tape).

application_notes

All measuring instruments are subject to limitations. The purpose of these application notes is to explain some of those limitations and to help the engineer maximise the many advantages of PEM’s Rogowski current transducers.

AN0019-The-application-of-the-Bartington-Fluxgate-Magnetometers-in-TDEM

This note describes an improvement to the TDEM method which will mostly concern mineral exploration, in which the main interest is highly conductive bodies, such as ore bodies. This is articularly the case for exploration for nickel or sulphides.

AN_181-CPCO-Cable-Options

The AKM EM-3242 Non-Contact Angle Position Sensing IC is a very small, low cost and easy to use angle position sensor with a continuous 360 degree range. The EM-3242 provides an absolute position output which means the power can be removed then reapplied and the output will continue to have the correct angle even if the rotating magnet moved while the power was off. The device requires very little power and operates at 3V+/-10%. The EM-3242 senses the angle of magnetic field component that is parallel to the plane of the device package and provides an analog output voltage of 10% to 90% of the supply voltage for a mechanical angle range of 360 degrees of rotation.The device includes a power down ( PDN ) function which reduces the current draw to less than 10uA.

AKM_DS_EM3242-AngleSensor

□ Small absolute rotary encoder □ Small input device (mode selector, volume control, and soon) □ Potentiometer □ Rotary switch

ACCT-S-198-MSH

Precise waveform measurement of long pulses and macropulses up to several milliseconds with minimal droop and noise.

ACCT-S-178

Precise waveform measurement of long pulses and macropulses up to several milliseconds with minimal droop and noise.

ACCT-S-175-MSH

Precise waveform measurement of long pulses and macropulses up to several milliseconds with minimal droop and noise.

ACCT-S-122

Precise waveform measurement of long pulses and macropulses up to several milliseconds with minimal droop and noise.

ACCT-S-082

Precise waveform measurement of long pulses and macropulses up to several milliseconds with minimal droop and noise.

16900450_B

The 3480 dipole electromagnet is a light weight versatile system that can provide fields approaching 4 Tesla. At 34 kg this magnet can easily be moved between applications and can be operated in any orientation.

11900202

The 3480 dipole electromagnet is a light weight versatile system that can provide fields approaching 4 Tesla. At 34 kg this magnet can easily be moved between applications and can be operated in any orientation.

17900-2209-0-Outline-Drawing

The 3480 dipole electromagnet is a light weight versatile system that can provide fields approaching 4 Tesla. At 34 kg this magnet can easily be moved between applications and can be operated in any orientation.

11907-0363-1_A_Gimbal_Mount_Basic_Dimensions

The 3480 dipole electromagnet is a light weight versatile system that can provide fields approaching 4 Tesla. At 34 kg this magnet can easily be moved between applications and can be operated in any orientation.

5972_Magnet_Control_Users_Manual

5972_Magnet_Control_Users_Manual USER’S MANUAL 5972 MAGNET CONTROL

5451 Magnet application

To avoid saturation, beam current transformers must be shielded from solenoid, quad and RFQ high stray fields.Good understanding of field distribution, shielding materials and techniques is required. Space availability imposes compact shields along the beam pipe.

5203_Eaton_Interlock_Logic

In an interlock event the protected power lines are disconnected, the unprotected lines remain powered. In this case, the power supplies lose power and the magnet is inert, the PC remains on.

3480_Brochure

The 3480 dipole electromagnet is a light weight versatile system that can provide fields approaching 4 Tesla. At 34 kg this magnet can easily be moved between applications and can be operated in any orientation.

3MTS QSMANUAL

This manual contains all relevant information on the steps, which are necessary to start the 3MTS Teslameter software installation and to operate it properly, once the 3MTS is connected to the PC or Tablet via the delivered USB cable. All files, including the software, user manuals and calibration data have been stored on the 3MTS USB flash memory stick, which is a part of the Teslameter package

SPI Supplies Vacu Prep II™

From the solid-state electronics for precise control and reproducibility to the convenient, easy to use touch screen interface, the Vacu Prep II is designed to be an easy to use instrument. The self-contained turbo molecular pump is capable of quickly reaching vacuum levels of 10-7 torr, while the large baseplate with multiple feed throughs accommodates a variety of fixtures to handle almost any application.

SPI Supplies® Brand Microanalysis Standards

High quality Standards for Microanalysis for any laboratory with EDS, WDS or EPMA

SPI Supplies Plasma Prep™ RIE

The SPI Supplies Plasma Prep Reactive Ion Etcher (RIE) uses a chemically reactive anisotropic plasma to etch and remove materials from package devices, wafers, and other substrates where a directional field is needed. In failure analysis labs, the use of wet etching for these samples is not only dangerous, in many cases it causes undercutting due to the isotropy of the etch. The Plasma Prep Reactive Ion Etcher uses dry etching to create an anisotropic etch—meaning that the etch is uni-directional

REBEKA BSE Detector

REBEKA™ combines the best available single crystal scintillators manufactured by Crytur with precise high-vacuum mechanics and readout electronics in one ready-to-use package.

K-kit ad

The K-kit system is an innovative tool that allows the examination of liquids in a TEM without the use of specialized TEM holders, feedthroughs or equipment. K-kits are sample holders designed to facilitate TEM observations of liquid samples, allowing nanoparticles, aggregates, and agglomerates to be characterized in the liquids. With vacuum compatible sealing of liquids in electrontransmitting thickness, K-kits are micro reaction chambers for countless experiments in materials, chemical and biological research.

FlipScribe

FlipScribe takes scribing to a new performance level, making clean, straight scribe lines on the back side to accurately cleave front side targets, bonded wafers and other substrates. This method eliminates contamination of sensitive front side devices during the scribing processes and is valuable for both crystalline and amorphous samples.

Apiezon H High Temperature Vacuum Grease Datasheet

Apiezon H grease is the ideal choice for use at higher temperatures across a wide variety of applications in both science and industry. The table opposite shows the key features of the product.

美国ARS-LT4液氦液氮型连续流低温恒温器

LT4系列连续流恒温器是经济连续流恒温器，可进行光电磁各种低温测试。 LT4既可以使用液氦也可以使用液氮进行工作。该系统包含标准的传输管线和冷指，也可根据客户需要进行定制。 典型特点 1. 液氦流 2. 铝制结构 3. 1.25英寸的大透明光学窗口 4. 大样品视角利于光学采集(F/1) 5. 4 K 液氦操作 6. 4.2K下液氦消耗率为0.75 LL/hr 7. 兼容液氮(77 K操作) 8. 可根据客户要求进行定制

美国ARSDS-LN400-液氮型低温恒温器

LN400液氮储槽型恒温器是经济连续流恒温器，可进行光电磁各种低温测试。 LN400使用液氮进行工作，工作温度77K至500K（高温可到800K），结构可根据客户需要进行定制。

美国ARS LT3B超高真空(UHV)管状连续流低温恒温器

LT3管状连续流低温恒温器应用十分广泛，拥有很多独特特点，如热交换型液氦传输管线可以提高制冷效率而且极大的消除振动。 LT3恒温器拥有不锈钢仪表群，独特的双O圈设计使它易于安装，校准，移除真空外罩。 LT3根据使用条件不同有很多不同设计，如： LT3K可与Newport Kappa测角器集成; LT3G可与Huber 5012.12集成，而且LT3G的小径向间隙使得其应用非常广泛; LT3B是真正的UHV冷头(10-11 Torr) ，该款恒温器都用焊接接头和金属密封取代了橡胶O圈密封; LT3M可定制冷指长度到1200mm,非常适合需要长冷指的表面物理实验。

美国ARS-DS-CS204AF-FMX-19N-非光学顶端装载型闭循环低温恒温器

X-19-NO是顶端装载样品的非光学型恒温器，样品置于氦气交换气体腔，使用样品杆更换样品，换样时无需关闭制冷机，这样的设计换样速度快，特别适合需要进行大量样品测试情况。而且样品置于冷的氦气环境中，适用于各种导热性不好的样品降温。 该系列恒温器尾部可做成非常细小，而且由无磁材料制成，特别适合匹配超导磁体进行磁化率及VSM测试。 X-19-NO系列恒温器可配备DE-202、DE-204或DE-210系列冷头。