美国ARS超低振动超精细闭循环低温恒温器X-20

TMI CCS Carbon Ceramic Sensor™ Type D

CCS sensors are the latest development of TVO resistors with a carbon ceramic composite construction which exhibit a single resistance verses temperature curve. CCS sensors are available calibrated or uncalibrated and offer exceptionally fast response times, excellent repeatability and long term stability, extremely robust and resistant to the harshest environments including magnetic fields and high dose radiation

Model SI-415 Silicon Diode Temperature Sensors

The Scientific Instruments Model Si-415 Silicon Temperature Sensors operate over a wide temperature range and are miniature in size. They are linear over a wide temperature range interval, and have high sensitivity in their lower range. The silicon diode temperature sensors are interchangeable to a standard V/T curve.

我司在深圳某高校成功安装美国ARS超高真空高效单级制冷机

近日在深圳某高校成功安装美国ARS（ADVANCED RESEARCH SYSTEMS）超高真空高效单级制冷机。

VIS-Datasheet-T56-850TB

The T56-850 transmitter optical subassembly combines an 850nm VCSEL and an optional driver IC integrated on a test board and fiber coupled with a 50/125 µm multimode fiber. The T56-850nm is designed for high speed data communication applications. The device is configured for differential drive and a controlled impedance circuit is available for optimum performance.

VIS-Datasheet-T56-250C_v1_1

The T56-250C is a high speed transimpedance amplifier (TIA) IC designed for use by 56G receiver modules in fiber optic transmission systems. The T56-250 operates from a single +3.3 V supply typically dissipating 250 mW of DC power and is designed for the use with PIN photodetectors in a wire-bond assembly The IC has a single-ended input (IN) and a differential output (OutP, OutN). It includes the cathode connection for the photodiode (Cath) as well as a bias path through the internal pin (PD). The TIA features input/output DCoffset cancellation and is equipped with various analog control pins (NoXing, Vxing, Vmod and BW) which allow for zero-crossing adjustment, gain and peaking control.

VIS-Datasheet-D50-1300M

These high speed photodetector modules consist of an InP pin photodetector integrated with a 50 µm-core diameter multimode fiber for optical input. The responsivity is greater than 0.5 A/W at 980 nm and 0.6 A/W at 1310nm. The modules are engineering samples and use an external DC.

VIS-Datasheet-A50-300C90

The A50-300C90 is a three stage high speed driver IC designed for the use with 50 Gbit/s optical modulated laser in fiber optic transmission systems. The A50-300C90 operates from a single +5 V supply. It features a high voltage drive capability and low power consumption.

helium_level1

The AMI family of liquid helium level instruments offer a wide range of solutions. All instruments pass a constant current through a superconducting Niobium Titanium (NbTi) filament and measure the resistance. The portion of the filament in liquid helium becomes superconducting (i.e. no resistance). The resulting resistance of the wire above the liquid is converted to a level signal. Advanced circuit designs offer our customers many advantages. Years of trouble free service are the result of rugged construction both inside and out. All our instruments and sensors from 1” to 36” are stock items for quick delivery. Our experienced staff offers prompt repair service when needed. OEM instrument design and manufacturing partnerships are always welcomed if our standard products do not meet your needs.

Cryogen_Free_Magnets_Info_Brief

The simplest magnet system is one where a sample insert has a small 6T magnet bolted at the bottom. Such an insert would have an integral variable temperature insert with sample space of 25 mm. These inserts are very effective in performing transport studies on nano size specimens and can be a useful tool to demonstrate the Quantum Hall Effect for educational purposes or for prescreening samples before they are tested at facilities that are not easily accessible.

LT4B

The ARS manufactured LT4B Helitran is a True UHV cold head (10-11 Torr) where all of the rubber o-ring seals have been replaced with welded joints and metal seals. The LT4B is our lowest cost liquid flow UHV cryostat. The LT4B works with either Liquid Helium or Liquid Nitrogen. The LT4 utilizes a standard transfer line and cold tip. In order to upgrade to our coaxial shield flow transfer line and angstrom level vibrations, you need to take a look at the high performance LT3B.

我司在深圳某高校成功进行了美国ARS低温恒温器与奥林巴斯（OLYMPUS）显微镜集成

近日我司在深圳某高校成功进行了美国ARS （ADVANCED RESEARCH SYSTEMS）低温恒温器与奥林巴斯（OLYMPUS）显微镜集成。

STT - shaft twist tester Flyer German

STT – Shaft Twist Tester Fertigungsnahe optische Drallprüfung von Radialwellen-Dichtringsitzen Um eine Undichtheit bei einer Radialwellendichtung zu vermeiden, ist die Dichtungsfläche der Welle drallfrei zu fertigen. Durch die optische Beugung können Drallstrukturen sichtbar gemacht werden, deren Amplituden deutlich unterhalb der Rauheitsamplituden der Dichtfläche liegen. Schnell und zuverlässig kann somit eine Qualitätskontrolle in unmittelbarer Nähe zum Bearbeitungsprozess erfolgen. Mit Prüfzeiten im Sekundenbereich sind die Geräte vielseitig einsetzbar z.B. für die Eingangskontrolle, für die Prozessoptimierung des Herstellungsverfahren oder für die 100% - Kontrolle in der Serienfertigung.

magview Flyer German

Der magview ist ein universell einsetzbares magnetooptisches Auslesegerät zur schnellen und präzisen Visualisierung magnetischer Strukturen. Als mobiles Handgerät kann er zur Qualitätssicherung und Streufeldanalyse eingesetzt werden. Visualisiert werden beispielsweise magnetische Streufelder von Magnetstreifenkarten, magnetischen Encodern, Dipol- und Multipolmagneten.

mageye Flyer German

Das mageye ist ein digitales Mikroskopkamera-System mit magnetooptischer Sensorspitze zur schnellen und präzisen Visualisierung magnetischer Streufelder. Das handliche System, inklusive Anwendungssoftware, erlaubt eine Echtzeitanalyse magnetischer Streufelder und ist beispielsweise für eine mobile Qualitätsprüfung von Schweissnähten bestens geeignet. Visualisiert werden ausserdem Streufelder von Magnetstreifenkarten, Audiobändern, magnetischen Encodern, abgeschliffenen Seriennummern sowie von Dipol- und Multipolmagneten.

Helmholtz Coils Flyer English

One of Matesy’s core competencies is the management of development projects. In cooperation with you, we create a concrete solution, manufacture a system according to your specific needs and support the implementation process.

m-axis Flyer German

m-axis is a measurement system to investigate the magnetic specifications of permanent magnetsm-axis is a measurement system to investigate the magnetic specifications of permanent magnets(magnetization angle and magnetic moment). Due to the modular setup it is possible to customizethe measurement range of the m-axis system in addition to the four standard ranges and for 100% quality control.

导电银环氧树脂胶EPOXY H20S 1OZ/组

EPO-TEK®H20S是EPO-TEK®H20E的改良版，主要用于芯片键合的模具冲压和点胶技术。 EPO-TEK®H20S是一种高度可靠，双组份的银填充环氧树脂，具有光滑触变粘稠性。 除了高导电性，短的固化周期，证明的可靠性，以及方便的配合比以外，EPO-TEK®H20S的使用是非常简单。

AtomicForceMicroscopy(AFM)

Atomic Force Microscopy (AFM) is one of the methods of scanning probe microscopy (SPM), which is a collective technique to measure local properties, e.g., height, friction, and magnetism. AFM consists of a sharp tip at the end of a cantilever as the probe, which is normally 3-6 μm tall pyramid and 15-40 nm end radius, to measure the force between the tip and the sample surface.

AtomicForceMicroscopy(AFM)原子力显微镜

原子力显微镜（AFM）是扫描探针显微镜（SPM）的一种方法，它是一种测量局部性质（如高度、摩擦力和磁性）的综合技术。AFM 由悬臂末端的尖端作为探针组成，探针通常为3-6μm 高的棱锥体，端部半径为15-40nm，用于测量探针与样品表面之间的作用力。

Photoluminescence

Photoluminescence (PL) spectroscopy is a widely used technique for the characterization of the optical and electronic properties of semiconductors and molecules. PL is a process of light emission from any form of matter after the absorption of photons. The incident photon in the visible region excites one of its electrons to the excited state. And then, it radiates a photon as the electron return to the lower energy state. In quantum mechanics, the energy band is quantized, which means only certain transitions are allowed. Therefore, the discontinued energy peaks of luminescence are expected.

PhotoelectricEffect

When light illuminates a material, due to the energy transfer from the light to the carriers in materials, electrons will be ejected from the surface. This effect is called the photoelectric effect, and the emitted electrons are called photoelectrons. According to experiments, the results show that only the light that exceeds the threshold frequency can generate photoelectrons. Below that threshold, no electrons are emitted from materials. That threshold is called the work function, which is attributed to the electron binding energy. The photoelectric effect experiments are commonly performed on quantum devices for characterization at cryogenic temperatures.

MössbauerSpectroscopy

Mössbauer spectroscopy is a spectroscopic method to detect a slight change in energy levels of an atomic through recoil-free resonant absorption and emission of gamma rays in solids. Typically, chemical shift,quadrupole splitting, and hyperfine splitting can be observed. Due to the narrow linewidth of gamma rays,Mössbauer is extremely sensitive in terms of energy resolution. In the resulting spectra, the gamma-ray intensity is plotted as a function of the source velocity. At velocities corresponding to the resonant energy levels of the sample, a fraction of the gamma rays are absorbed, resulting in a drop in the measured intensity and a corresponding dip in the spectrum. The absorbing nuclei and sample can be characterized by the number, positions, and intensities of the dips in the spectrum. Recently, some charge state and electronic configurations have been confirmed through Mössbauer spectroscopy at cryogenic temperatures.

MatrixIsolation

Matrix isolation is a spectroscopic study to maintain materials (guest particles) in an inert medium (host matrix) at very low temperatures. It was developed because it’s difficult to obtain gas-phase infrared spectra due to its high chemical reactivity of transient molecules. The mixture of guest particles and the host matrix is deposited on a transparent window, which will be cooled below the melting point. Experiments must be performed under a high vacuum to prevent contaminants from unwanted gases freezing to the cold window.Lower temperatures are preferred, due to the improved rigidity and "glassiness" of the matrix material. Noble gases are normally used to dilute guest samples, such as argon, not just because of their unreactivity but also because of their broad optical transparency in the solid-state.

Magneto-OptoKerrEffect

Magneto-Opto Kerr Effect (MOKE) is a technique to investigate the magnetization structure of materials by the change in intensity and polarization of reflected light from the magnetized surface. MOKE is one of the magneto-optic effects. Kerr effect, investigating reflected light, is similar to the Faraday effect, which is to detect the transmitted light. Upon the direction of the magnetization vector with respect to the reflecting surface and the incident plane, there are polar MOKE, longitudinal MOKE, transversal MOKE, and quadratic MOKE. In addition, low-temp MOKE helps characterize superconductor/magnetic materials in terms of current density and magnetic flux distribution.

Fourier-TransformInfraredSpectroscopy(FTIR)

When a sample is exposed to infrared radiation, the dipole moment will be excited by absorbing the radiation with a specific wavelength. The vibrational energy will be excited from the ground state to the excited state.Unlike dispersive spectroscopy, Fourier-transform infrared spectroscopy (FTIR) contains many frequencies of light at once and measure absorption. Next, the beam contains a different combination of frequencies of light and repeat it. After repeating several times, the raw data will be processed to resulting data cm-1, wavenumber.This process is called the Fourier Transform.

Fourier-TransformInfraredSpectroscopy(FTIR)傅立叶变换红外吸收光谱学

当样品暴露在红外辐射下时，通过吸收特定波长的辐射激发偶极矩。振动能量将从基态激发到激发态。与色散光谱学不同，傅立叶变换红外外吸收光谱（FTIR）同时包含多个光频率并测量吸收。接下来，光束包含不同频率的光并重复它。重复几次后，原始数据将被处理为结果数据cm-1，wavenumber。这个过程称为傅立叶变换。

Ellipsometry椭圆偏振技术

椭圆偏振法是一种测量薄膜介电特性的光学方法。偏振光从样品表面斜反射，产生偏振反射光的振幅比和相位差椭圆，用椭圆偏振光谱仪测量，成分、粗糙度、厚度等信息，通过它可以得到掺杂浓度和其它材料特性。薄膜的本征物理性质也可以用椭偏仪的温度依赖性来研究。

Deep-LevelTransientSpectroscopy(DLTS)深能级瞬态谱

深能级瞬态光谱（DLTS）是通过测量电容瞬态随温度变化来检测半导体深能级缺陷浓度和热发射速率的有力工具。它通常使用肖特基二极管或p-n 结作为探针。在此过程中，探针正向偏压，以脉冲电压填充自由载流子缺陷。脉冲后，由于热发射，缺陷开始发射捕获载流子。

Angle-ResolvedPhotoemissionSpectroscopy(ARPES)

Angle-Resolved Photoemission Spectroscopy (ARPES) is one type of photoemission spectroscopies to obtain information about the electronic band structure and Fermi surface of crystals in the reciprocal space. Soft X-ray is irradiated onto the crystal surface, and the kinetic energy of photoelectrons emitted from the surface is measured as a function of polar and azimuthal angles. Because electrons escape from the surface are projected through the surface, the direction of the momentum perpendicular to the surface is not conserved. Therefore, ARPES is an ideal tool for 2D materials because the direction of the electronic momentum of interest is parallel to the surface. The increased sensitivity of excitations can be achieved by reducing thermal energy at cryogenic temperatures.

Angle-ResolvedPhotoemissionSpectroscopy(ARPES)角分辨光电子能谱

角分辨光电子能谱(ARPES)是一种用于获取晶体在倒易空间中的电子带结构和费米表面信息的光发射光谱法。用软X 射线辐照晶体表面，测量了表面发射的光电子动能随极角和方位角的变化。因为从表面逸出的电子通过表面投射，垂直于表面的动量方向不守恒。因此，RPES 是二维材料的理想工具，因为感兴趣的电子动量方向与表面平行。通过降低低温下的热能，可以提高激发的灵敏度。

DiamondAnvilCell金刚石压砧

金刚石顶砧（DAC）是一种实验性的元件，它通过用两个相对的金刚石压缩一小块材料来产生极端压力。压力通常可达100-200 GPa。这项技术的目标是模拟行星内部的环境来合成材料并观察在正常大气环境下不会发生的相位。样品可以通过钻石观察，也可以进行光学测量，如X 射线衍射、穆斯堡尔谱和光致发光。通常，样品可通过电阻加热至1000°C 或激光加热至5700°C 进行加热。DAC 实验也可在低温下进行，DAC 实验也可以根据不同的目的在低温下进行。

ThermoelectricEffect

The thermoelectric effect is the relationship between thermal and electric. When a temperature difference is created on both sides of the device, carriers in material diffuse from the hot side to the cold side, which results in a voltage across the device. Conversely, when a voltage is applied, heat is transferred from one side to the other, a temperature gradient is created. The thermoelectric effect generally consists of three effects, Seebeck effect, Peltier effect, and Thomason effect.

Magnetotransport

When quantum materials, especially 2D materials or multilayers, are subject to the magnetic field during the electron transport at low temperatures, the trajectory of the electrons and the electronic spins need to be taken into account. Quantum Hall effect, a quantum mechanical version of the Hall effect, is one of the phenomena. It is frequently used to characterize modern quantum materials with magnetoresistance.Magnetoresistance is a phenomenon of change in the resistance when a sample submitted to a magnetic field.When a sample contains ferromagnetic metals, the interplay of the magnetization of the sample and spin-polarized current is involved. The electrical resistance may chance through magnetoresistance effects that originate from different physical phenomena, such as giant magnetoresistance and tunnel magnetoresistance effects, which lead to the subject of Spintronics.

NobleGasAnalysis惰性气体分析

惰性气体，也就是氦(He)、氖(Ne)、氩(Ar)、氪(Kr)、氙(Xe)形成了一组性质相似的化学元素，如无味、无色和单原子。最重要的是，它们在化学上不发生反应。因此，它们也被称为惰性气体。由于惰性气体的化学和生物惰性以及放射性衰变所产生的独特同位素特征，惰性气体通常被用于探测海洋和地球过程，例如岩石和矿物年代测定。

ElectronParamagneticResonance(EPR)ElectronSpinResonance(ESR)电子顺磁共振电子自旋共振

电子顺磁共振(EPR)/电子自旋共振(ESR)是研究有机和无机自由基、过渡金属配合物和一些生物分子中未配对电子的重要方法。当具有不成对电子自旋的顺磁性化合物在磁场和电磁波(通常在微波频率范围内)作用下，就会诱导自旋态之间的跃迁。测量一般是在恒定频率下进行，而磁场是变化的。EPR/ESR 光谱仪测量电磁辐射的吸收。 由于电子自旋的弛豫时间短，EPR/ESR 必须在低温下进行。

X-rayDiffraction

X-ray Diffraction (XRD) is a technique to determine the atomic and molecular structure of a crystal based on Bragg diffraction. X-rays are commonly used to produce the diffraction pattern because their wavelength is typically the same order of magnitude (1–100 angstroms) as the spacing d between planes in the crystal. The information on the intensity and angle of the diffractive X-rays can produce a 3D picture of the density of electrons within the crystal, which leads to the mean positions of atoms as well as chemical bonds, disorders, and other information. If it’s a single crystal sample, it’s usually mounted on a goniometer, which can position the sample at selected orientations. The benefits of the low-temperature XRD are to reduce the radiation damage and thermal motion. Low-temperature XRD also helps characterize superconductor materials.

Vacuum Wire Wiring Accessories

Kapton® and Teflon® — Insulated wires for HV and UHV vacuum applications. Specialty and Thermocouple wire — T/C bare wire in matched pairs. Wiring Accessories — complete assortment of pins, tools, components, etc.

Vacuum Hardware

Vented Fasteners / Screws — Provide an excellent path for trapped gases to escape the bottom of blind-tapped holes. Three standard types available for shipping the same day. Custom bolts and screws are available on request. CF Flanges and Mounting Hardware — available with same day shipping. ISO KF and LF Flanges and Mounting Hardware — are also available for the immediate needs of our clients.

Thermocouple Feedthroughs

Type-K — Offers broadest temperature range (-200°C to +1250°C), and is the most widely used thermocouple type. For these reasons Accu-Glass supports Type-K with feedthroughs having Chromel® and Alumel® pins and mating contacts for maximum accuracy. Matched pin material for Type-T, J, E, S, R and C thermocouple are not available. Use of standard instrumentation feedthroughs with gold-plated nickel-iron alloy pins, and goldplated copper alloy contacts are offered instead. The error introduced using these pins and contacts is less than 2%. Cable Assemblies — Air side and UHV cable assemblies for all thermocouple types. Refer to specific cables for construction details.

Breaks Fluid Feedthroughs

Vacuum Breaks — excellent voltage isolation in both UHV and HV environments.Constructed using high purity alumina ceramic sealed to stainless sleeve adapters. Water, Fluid Breaks — voltage isolation in water or coolant fluid lines. Soldering or brazing requires low temperatures below 700°C. Standard adapters fit 1/4 to 1/2 Inch diameter tubes. Cryogenic, Fluid Breaks — great voltage isolation for cryogenic fluid lines. Designed to be TIG welded into cryogenic fluid transmission lines with 1/8 to 3/8 Inch diameters.Allows safe operation to –200°C.

我司在北京某高校成功安装美国ARS用于瞬态光栅的超稳型低温恒温器

美国ARS是一家世界级低温系统生厂商，创立于1986年，致力于为科研工作者提供1.5-800K低温解决方案。 ARS以研发为重点，生产的低温设备随着科学研究领域的不断变化而不断发展，为您提供最先进的低温设备。 ARS在全球拥有训练有素销售及技术团队，为客户提供售前售后技术支持，并以合理的价格为客户选择适合客户需求的低温设备。X20-OM超低振动超精细闭循环恒温器是特别为光学显微实验设计，如显微-光致发光(Micro-PL)，显微拉曼等。

LT4-FTIR

LT4-FTIR系列连续流恒温器是性价比高的FTIR连续流恒温器，专门用于FTIR低温测试。 LT4-FTIR既可以使用液氦也可以使用液氮进行工作。该系统包含标准的传输管线和冷指，也可根据客户需要进行定制。

X-15EPR闭循环低温恒温器

X-15系列低温恒温器专为低温电子顺磁共振（EPR）和电子自旋共振（ESR）而设计。O圈密封的石英样品小池使得系统可在不拆卸整套设备的前提下方便换样。可选蓝宝石或铜样品管。

±1T磁场强度下显微光学测试

典型特点：灵活性高，降温时间更短，换样方便 这套系统尾部可以最多可加5个窗口，样品处真空罩宽度19mm。（配合电磁铁可以获得高于1T的磁场强度） 该套样品处最低温度小于8K。（可连续变温，也可升级制冷机获得更低温度） 超低振动：恒温器固定安装振动3-5nm，恒温器配移动支架振动优于500nm。

ARS水冷机

美国ARS 水冷机   标准电压  频率 60 Hz 50 Hz 最小 200 V 200 V 最大 230 V 230 V 制冷量 3.9 kW 3.9 kW

X-1AL标准光学型闭循环低温恒温器

X-1AL系列标准光学型闭循环低温恒温器因其测试灵活，价格经济而成为绝大多数实验室样品及装置测试的最优选择，该系统广泛应用于各种光、电、磁测试。 X-1AL系列恒温器可配备DE-202或DE-204系列冷头，根据客户需要可选择4K，5.5K，10K不同型号。

ds.MG80.Cooler

Typical Applications • LN2 Replacement • IR Laser Diode Cooling • CCD Detectors • Raman Detectors • Infrared Detectors • Mobile Communications • Cold traps • Optics • Electronics (LNAs, HTS, CMOS, Etc.)

ds.cs210-x5

Closed Cycle Cryostat for Neutron Scattering Experiments. The CS-210 is a high power cooler with fast cooldown and high cooling power.

ds.cs210-x3

Closed Cycle Cryostat for Non Optical Experiments, sample in vacuum. The CS-210 is a high power cooler with fast cooldown and high cooling power on both stages.

ds.cs202-x15

The Displex cryocooler is perfectly suited for EPR experiments at controlled low temperatures in Laboratories where Liquid Helium is impractical or where long duration experiments are frequently performed. These cryogen free systems can regulate the sample temperature between 4K and 450K

ds.cc210

Unique Features: • Cooling power on first stage is higher than comparable systems for cooling larger radiation and other parasitic heat loads for magnet cooling. • Pneumatic Drive Displex Cryocooler for low vibrations at the sample (see Specifications). • Only two moving/Wearing components for high reliability. • Displacer can be removed from the cryocooler for maintainence in the field without breaking vacuum. • Tunable for high performance at any heat load. • Easy field maintenance. Low life cycle cost. • Compressor Model ARS-10HW is water cooled for quiet and clean operation. • Low cooling water flow rate.

ds.cc202

The ARS Pneumatic Drive Cryocooler is a two component closed cycle system operating in the temperature range 3K to 300K. It has no mechanical drive linkages making it very low maintenance and reliable. The displacer motion is controlled by the differential gas pressure, this results in low vibrations at the second stage of the cryocooler.

ds.windowmaterials

Optical specifications of window materials. ARS cryostats are available with a large selection of optical windows for UV, Vis and IR experiments. UV - .1 to .3 Microns (100 - 300 Nanometers) VIS - .3 to 1 Microns (300 to 1000 Nanometers) IR - 1 + Microns ( 1000 nanometers)

ds.samplehldrs

Optical (Transmission). 0.75 in. clear view. Flat Plate:Backscattering

ds.floor-stand

ARS Floor Stand for Ultra-Low Vibration Interfaces ·Adjustable height ·Extruded aluminum construction ·Wheels for moving stand

CryogenicFacts

Temperature measured with heat load applied @ cryocooler 2nd stage cold tip with no cold tip attachments, with cold tip vertically down, @ 60Hz power, @ room ambient (19-25C), with full radiant heat shield attached to 1st stage, with no additional applied 1st stage heat load, high vacuum insulation (starting vacuum <10mtorr with < 5mtorr/min rate-of-rise), 10’ flexhoses (3/4” dia for 204S and 210S). 50 Hz reduces capacity and increases cooldown times 15-25%. Data is typical but not guaranteed.

ARSJTCooler(ORCA)

The ARS MR JT coolers use a patented unique cooling cycle to cool down and maintain temperatures to -193C (80K) without the use of liquid cryogens. The system consists of three physical components • Cold Head – where refrigeration occurs • Compressor – provides refrigerant flow & pressure • Gas Lines – room temperature, self sealing

DS-PSF-EM-10-4

This model of the ARS Probe Station is designed for the ultimate in flexibility for non-destructive device testing. This system provides a .6T Horizontal Magnetic Field and comes with a BiPolar Power Supply.

DS-PSF-10-4

This model of the ARS Probe Station is designed for the ultimate in flexibility for non-destructive device testing. The ability to upgrade and modify this system for further device testing has been in the forefront of this design.

ds.cs202-x2c

Closed Cycle Cryostat Full featured cryostat for x-ray diffraction. Fits on Diffractometers listed below. Welded skirt with "G" configuration which turns all the hose and feedthroughs 90º for safe rotation during the experiment.

DS-CS210AF-GMX-20

The CS210*F-GMX-20 pairs our largest cryocooler, the DE-210, with our X-20 Ultra Low Vibration interface to offer unprecedented cooling power at nanometer vibration levels. The CS210*F-GMX-20 uses a Helium Exchange Gas to decouple the sample space from the cold tip of the DE210 Cryocooler. This prevents almost all vibration from being transmitted to the sample. Because the exchange gas is inherently less efficient than cooling by conduction, t the base temperature of the sample may be ~1K higher than the cryocooler. Additionally the GMX-20 interface requires the cold tip down orientation to facilitate convective cooling of the exchange gas.

DS-CS204AF-DMX-20

The CS204*F-DMX-20 opens up a wide range of possibilities never before possible with a closed cycle cryocooler. The DE204*F-DMX-20 uses a Helium Exchange Gas to decouple the sample from the cold tip of the DE204 Cryocooler. This prevents almost all vibration from being transmitted to the sample. Sample vibration levels of 3-5nm have been demonstrated by users. Due to the exchange gas being less conductive, the base temperature will increase by 1-2K and the cooling Capacity is roughly cut in half at varying temperatures.

DS-CS202AF-DMX-20

The CS202*F-DMX-20 opens up a wide range of possibilities never before possible with a closed cycle cryocooler. The DE202*F-DMX-20 uses a Helium Exchange Gas to decouple the sample from the cold tip of the DE202 Cryocooler. This prevents almost all vibration from being transmitted to the sample. Sample vibration levels of 3-5nm have been demonstrated by users. Due to the exchange gas being less conductive, the base temperature will increase by 1-2K and the cooling Capacity is roughly cut in half at varying temperatures.

ds.cs202-x15

Closed Cycle Cryostat for EPR The Displex cryocooler is perfectly suited for EPR experiments at controlled low temperatures in Laboratories where Liquid Helium is impractical or where long duration experiments are frequently performed. These cryogen free systems can regulate the sample temperature between 4K and 450K

DS-CS204AI-FMX-1SS

The CS204*I-FMX-1SS is our standard intermediate cooling power cryostat for optical and electri-cal measurements. This high performance system offers and all stainless steel constructed vacu-um shroud along with a welded stainless steel instrumentation skirt. This system is capable of achieving vacuum levels of 10-7 Torr with an appropriate vacuum system.

DS-LT3M

The ARS manufactured LT3M Helitran is a True UHV cold head (10-11 Torr) where all of the rub-ber o-ring seals have been replaced with welded joints and metal seals. Like all of our LT3 helium flow cryostats, the LT3M is an advanced liquid helium flow cryostat utilizing many unique features, such as the matrix heat exchanged and the coaxial shield flow transfer line to achieve unparalleled efficiency and ultra low vibration levels. The combination of True UHV and angstrom level vibrations makes the LT3M ideal for low temperature application. The extended length and addition of a rigid support tube allow for cleaving and manipulation.

DS-CS204AF-FMX-19OP

The OmniplexTM, DE204*F-FMX-19OP, is a top loading optical cryostat with the ARS manufactured DE-204 cryocooler. The ARS OmniplexTM systems features large optical access and quick sample change. The OmniplexTM comes with 4 window ports and with warm and cold windows. The sample stick can use any of the starndard ARS sample holders as well as receive a second set of temperature control instrumentation for fine tuning of the sample temperature. The system allows for a fast intial cooldown (~90 min to 20K and 2 1/2 hrs to base temperature).

原子力显微镜(AFM)&扫描近场光学显微镜(SNOM)形貌

ARS 公司推出了一款专门替代液氦制冷的低温AFM/SNOM 平台的超级优越的经济型无液氦解决方案。

AirDryAgSelectorGuide

DuPont Conductive Silver Compositions for General Purpose Air-Dry Applications

美国GMW-hw-322b_gmw

Please be aware that AKE products are not intended for use in life support equipment, devices, or systems. Use of AKE products in such applications requires the advance written approval of the appropriate AKE officer. Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks,adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of AKE products in such applications is understood to be fully at the risk of the customer using AKE devices or systems.

美国GMW-hw-108a_gmw

Please be aware that our products are not intended for use in life support equipment, devices, or systems. Use of our products in such applications requires the advance written approval of our sales staff.Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks,adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of our products in such applications is understood to be fully at the risk of the customer using our devices or systems.

美国GMW-hw-105a_gmw

Please be aware that our products are not intended for use in life support equipment, devices, or systems. Use of our products in such applications requires the advance written approval of our sales staff. Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks, adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of our products in such applications is understood to be fully at the risk of the customer using our devices or systems.

美国GMW-hg-0814_e

•Please be aware that our products are not intended for use in life support equipment, devices, or systems. Use of our products in such applications requires the advance written approval of our sales staff. Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks,adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of our products in such applications is understood to be fully at the risk of the customer using our devices or systems. •Handling precautions required for preventing electrostatic discharge. •This product contains galium arsenide（GaAs）.Handling and discarding precautions required.

美国GMW-hg-0812_e

•Please be aware that our products are not intended for use in life support equipment, devices, or systems. Use of our products in such applications requires the advance written approval of our sales staff. Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks, adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of our products in such applications is understood to be fully at the risk of the customer using our devices or systems. •Handling precautions required for preventing electrostatic discharge. •This product contains galium arsenide（GaAs）.Handling and discarding precautions required.

美国GMW-AN_160

The AN_160KIT is a Universal Hall Interface Module (UHIM) which provides an easy means to evaluate the Asahi Hall elements for magnetic field, electric current or position sensing applications.The UHIM consists of a differential amplifier, a voltage drive circuit for Hall elements requiring a voltage drive, a current drive circuit for Hall elements requiring current drive, and two analog output circuits to provide the standard 2.5V ±2.5V signal and a 1.5V ±1.5V signal for 0-3V input level A/D circuits.

VWM-S-1W-assembly

Requirements and tools 1. All new sensors are delivered with a wire pre-installed. Its tension is arbitrary. Its purpose is to allow immediate functional check of the sensor. 2. To install new wire, its length should be approximately 60mm longer than the sensor. Wire must be clean without visible damage or bending. 3. Necessary tools: - Screwdrivers with hexagonal ball heads 1.5mm, 2mm and 2.5mm - Tweezers - 2-3 surgical-style clamps - Scales with range ≥0.5kg - Set of weights to hook to surgical clamp - Magnifying glass - DVM 4. All sensors are thoroughly cleaned for UHV before shipment. A Residual Gas Analysis is attached. If sensors are to be used in UHV, it may be necessary to clean them again after manipulation. Laboratory-standard UHV cleaning techniques can be applied

VWM-S-1W-A40mm-RightView

VWM-S-1W-A40mm-RightView VWM-S-1W-A40mm-RightView VWM-S-1W-A40mm-RightView

VWM-S-1W-A20mm-MainView

VWM-S-1W-A20mm-MainView VWM-S-1W-A20mm-MainView VWM-S-1W-A20mm-MainView

VWM-S-1W-A5mm-TopView

VWM-S-1W-A5mm-TopView VWM-S-1W-A5mm-TopView VWM-S-1W-A5mm-TopView

VWM-S-1W-A5mm-RightView

VWM-S-1W-A5mm-RightView VWM-S-1W-A5mm-RightView VWM-S-1W-A5mm-RightView

VWM-S-1W-A5mm-MainView

VWM-S-1W-A5mm-MainView VWM-S-1W-A5mm-MainView VWM-S-1W-A5mm-MainView

VWM-S-1W-A5mm-FrontView

VWM-S-1W-A5mm-FrontView VWM-S-1W-A5mm-FrontView VWM-S-1W-A5mm-FrontView

VSM-paper-accepted

A simple Vibrating Sample Magnetometer for macroscopic samples

TNG3DTM003a

The Group3 Digital Teslameter is a precision electronic measuring device. Because of the nature of the measurements it is asked to do it is frequently exposed to conditions that are considerably worse than is normally encountered by precision instruments. Because of this due care has to be taken when installing it.

TNG3DTM002a

Caution: The following procedure requires working with and around high voltages. Please exercise extreme caution when doing so, or refer to a qualified person to do the work for you. For proper grounding and transient protection of the Group3 DTM, please refer the drawing number 11901610 and follow the steps outlined below.

TN_FCT_04-08r1

This Bergoz Instrumentation TechNote compares data taken on a real beam with data taken in the lab before shipment using an instrument-simulated beam, in order to predict the performance of an In-flange.FCT after it is installed on the beam.

THM1176-MF-and-HF-Sensor-Head-Dimensions

THM1176-MF AND THM1176-HF SENSOR HEAD DIMENSIONS – REV. B

Thermo_Fisher_Chiller_1490G-CIRC_Manual

Thermo Scientific ThermoFlexTM Recirculating Chillers (Deluxe Controller)

The-Parametric-Current-Transformer-A-Beam-Current-Monitor-Developed-for-LEP

Toroidal transformers are used to measure the beam current in beam lines and accelerators. Placing such a transformer hi the feedback loop of an operational amplifier will increase the useful frequency range (active current transformer). A magnetic modulator can be added to extend the response to DC current, maintaining with a control loop the transformer core at a zero flux state.

The-Parametric-Current-Transformer

Toroidal transformers are used to measure the beam current in beam lines and accelerators. Placing such a transformer hi the feedback loop of an operational amplifier will increase the useful frequency range (active current transformer). A magnetic modulator can be added to extend the response to DC current, maintaining with a control loop the transformer core at a zero flux state.

stulle_inpac2018

The CWCT is a novel instrument developed for the accurate determination of the CW beam average current. It measures average beam currents down to the microampere level with noise contributions below 1 μA. Its output signal follows beam current fluctuations within ≤1 μs, permitting fast detection of beam loss. These characteristics render the CWCT an ideal instrument for proton and ion accelerators. We present the CWCT principle and laboratory measurements using various input signals.

SOR-MAN-SGA

AMETEK, Inc. is a leading global manufacturer of electronic instruments and electromechanical devices with annualized sales of $2.5 billion. The Company has over 11,000 colleagues working at more than 80 manufacturing facilities and more than 80 sales and service centers in the United States and around the world.

SOR-DS-SG-Datasheet

The Sorensen SG Series (hereafter SG Series) represents the next generation of high power programmable DC power supplies. The SG Series is designed for exceptional load transient response, low noise and the highest power density in the industry. With a full 15 kW available down to 20VDC output in a 3U package the SG leads the industry in power density. The power density is enhanced by a stylish front air intake allowing supplies to be stacked without any required clearance between units.

SN-DS-hall-probe-g-for-i1a-mft

Hall Probe G for F1A Magnetic Transducers with the naked Si chip is a very thin (0.5mm) and long (42mm) single-chip integrated 1-axis Hall-Probe. It measures magnetic fields perpendicular to the probe plane (By).

Shape-E-SMA

CURRENT TRANSFORMER- SHAPE E/SMA CONNECTOR CURRENT TRANSFORMER- SHAPE E/SMA CONNECTOR

Shape-C-SMA

CURRENT TRANSFORMER- SHAPE C/SMA CONNECTOR CURRENT TRANSFORMER- SHAPE C/SMA CONNECTOR

Shafer-BPM

The purpose of this paper is to review the topic of beam position monitoring as it applies to charged-particle beams in accelerators and beamlines.

SENIS-CS_Spec

The SENIS CS series current sensors offer low current sensing with high voltage isolation capability. The SENIS CS sensor incorporates the Melexis MLX91206 high sensitivity Hall IC and a multi-turn coil to further increase sensitivity.

rotating-stage_rftm

? Direct-drive concept provides faster rotating speeds and enhanced position sensitivity ? Ultra-low profile design – only 45 mm in height ? High efficiency DC step-motor optimizes available torque ? Proprietary glass scale encoder ensures 0.005°repeatability ? 6 mm diameter through-hole for convenient cable routing

RD101-EM3242

The RD101-EM3242 is a reference design for the AKM EM-3242 Non-Contact Angle Position Sensing IC. The EM-3242 senses the angle of magnetic field component in the top plane of the device package. The EM-3242 provides an analog output voltage of 10% to 90% of the supply voltage for a mechanical angle range of 360 degrees of rotation. The EM-3242 has two operating modes. One with the “In Range” detector enabled and one with the “In Range” detector disabled. The “In Range” detector includes internal circuitry which causes the output voltage to drop to 0V whenever the magnetic field level at the EM-3242 is greater than 60mT or less than 10mT.

RCTrms-Technical-notes

All measuring instruments are subject to limitations. The purpose of these technical notes is to explain some of those limitations and to help the engineer maximise the many advantages of PEM’s Rogowski current transducers. These technical notes should be read in conjunction with the RCTrms short-form datasheet.

RCTi-Technical-notes

All measuring instruments are subject to limitations. The purpose of these technical notes is to explain some of those limitations and to help the engineer maximise the many advantages of PEM’s Rogowski current transducers. These technical notes should be read in conjunction with the RCTi and RCTi-3ph short-form datasheets.

RCT1a

The RCT1A is a genuine Current Transformer (CT) replacement but hasall the intrinsic benefits of a thin, light-weight, flexible, clip-around Rogowski(sense) coil. Just like a CT the RCT1A secondary output is an industrystandard 0 to 1A (5VA pf 1) instantaneous current proportional to themeasured primary current.

PPM-DS-p2p-PowerSleeve

The PowerSleeve has been developed by PPM to allow the complete range of AC and DC point2point fibre optic plug in modules to be battery powered. Now users have the ability to take standard transmit or receive modules and fit it into the PowerSleeve instead of relying on mains power. This option is particularly important when locating point2point modules in remote locations that have limited access, where galvanic isolation is required or where no mains power supply is present.

PPM-DS-p2p-DCLink

The new DC point2point link is capable of transmitting analogue signals of up to 40MHz over singlemode fibre. This is equivalent to rise times of 10.3ns making it ideal for measuring HV transients on HVDC transmission lines. The modules are available in a fully EM shielded casing, or as a plug-in module for use with the various point2point housings.

PEM-TN-CWT-DelayAndRiseTime

The CWT behaviour at frequencies approaching and exceeding its specified (-3dB) bandwidth is very complicated. It is related to the distributed inductance and capacitance of both the Rogowski coil and the connecting co-axial cable (which have different characteristic impedances) and their terminations, and to the gain-frequency characteristic for the op-amps and associated parasitic impedances used to implement the integrator and buffer electronics. It also varies depending on the position of the current within the loop, although up to the (-3dB) bandwidth this variation is very small.

PAC1989_1993

? The connector body is connected to the cable shield. ? The wires at the end of the cable are soldered about 10mm.

PA1-Power-Amplifier-OM3225

Operation Manual for PA1 Power Amplifier Operation Manual for PA1 Power Amplifier

OM2914-Degaussing-Wand

Operation Manual for Degaussing Wand Operation Manual for Degaussing Wand

NPCT-175

NPCT-175 NPCT-175 NPCT-175 NPCT-175 NPCT-175 NPCT-175

NPCT-75

NPCT-75 NPCT-75 NPCT-75 NPCT-75 NPCT-75 NPCT-75 NPCT-75

MX-BPM_101_gain_adjust

The gains can be adjusted over a wide range by changing a few components: Xgain is determined by the equivalent resistance of R177 in parallel with R176. Ygain is determined by the equivalent resistance of R161 in parallel with R162

MS3-USB-Cable-DR2373

MS3 USB Cable Assembly MS3 USB Cable Assembly MS3 USB Cable Assembly

MS2-OM0408

Operation Manual for MS2 Magnetic Susceptibility System

MS2G-drawing

MS2G magnetic susceptibility sensor MS2G magnetic susceptibility sensor

MS2F-DR0640

MS2F-DR0640 MS2F-DR0640 MS2F-DR0640 MS2F-DR0640 MS2F-DR0640

MS2_MS3-DS0020

MS2/MS3 Magnetic Susceptibility System MS2/MS3 Magnetic Susceptibility System

MotorDrive2016-GMWPresentation

Accurate Power Conversion Measurements on High Power Motor Drives

Model_5201_mapa_data

Model 5201 Projected Field Electromagnet Field Map Data

MLVMCTRL-GMW-Magnet-Control-Software-manual

USER’S MANUAL MODEL: LVMCTRLLABVIEW MAGNET CONTROL

ML_TN_THM1176-HF-as-a-Thermometer

In order to compensate for temperature drift, the THM1176-HF sensor includes a temperature sensor. The THM1176 command set allows reading its value. Does this mean that I can use the THM1176 as a thermometer?

MFC3039

ASSEMBLY INSTRUCTIONS FOR THE MFC-3039 ROTATING PROBE-ARRAY HOLDER

Matesy-MO-PRES-SometimesPerspectiveDoesMatter

The magneto-optical technology is an imaging method for magnetic measurement, forensic investigation and non-destructive testing. The magneto-optical wafers provide field analysis and quality assurance of different magnetic materials. Magneto-optical wafers with different measuring ranges are available in standard sizes, customized geometries and as sensor array up to 100 x 100 mm.

Matesy-MO-DS-MagnetoOpticalSensors

The magneto-optical sensor technology is an imaging method for magnetic measurement, forensic investigations and non-destructive testing. The sensor technique enables field analysis and quality assurance of different magnetic materials. Magneto-optical sensors with different measuring ranges are available in standard sizes, customized geometries and as sensor array up to 100 x 100 mm.

Matesy-MAN-MagEye

Matesy-DS-MagEye Matesy-DS-MagEye User Manual MagEye

Matesy-MAN-CMOS-MagView

The CMOS-MagView is an innovative device for the optical visualization of magnetic fields. The highly engineered magneto-optial sensor technology visualize the magentic stray field of magnetic materials directly and at high optical resolution. The magneto-optical analysis of the test specimen provides concrete information about the field polarity, field homogeneity, distribution of the magnetic material and the magnetization properties.

Magnetic-Field-Mapping-System-MMS-1A-RS

MMS-1A-RS, the high-end version of the SENIS Magnetic Field Mapping System allows users to perform a fast, high resolution mapping of magnetic field around an permanent magnets, electromagnets and electronic circuit PCBs. The map of the magnetic field can be presented as color coded 2D or 3D isometric visual display on a PC screen and as a table of numerical values of the magnetic field (each component Bx, By, Bz, Bxy, Btot, etc.).

Mag690-DR2687

Mag690-DR2687 Mag690 Outline Drawing Mag690 Outline Drawing

EW-632

EW-632 is composed of a Ultra-high sensitive InSb Hall element and a signal processing IC chip in a package.

ew-450_gmw

EW-450 is composed of a Ultra-high sensitive InSb Hall element and a signal processing IC chip in a package.

ew-412b_gmw

EW-412B is composed of a Ultra-high sensitive InSb Hall element and a signal processing IC chip in a package.

EQ-733L_MS-1381-E-00_120508-gmw

• Analog output voltage proportional to the magnetic flux density • Magnetic sensitivity 20mV/mT (typ.) • Supply voltage from 3.0V to 5.5V at single power supply • Operating temperature range from -40°C to 100°C • Ratio-metric analog output • 3pin single in-line package (SIP), Halogen free • Quick response 1μs (typ.) • Low output noise voltage 2mVp-p

eq-433l_e

EQ-433L is composed of an InAs Quantum Well Hall Element and a signal processing IC chip in a package Notice:It is requested to read and accept "IMPORTANT NOTICE" written on the back of the front cover of this catalogue.

eq-430l_e

EQ-430L is composed of an InAs Quantum Well Hall Element and a signal processing IC chip in a package Notice:It is requested to read and accept "IMPORTANT NOTICE" written on the back of the front cover of this catalogue.

EPO_Control_Users_Manual_Pages

EPO_Control_Users_Manual_Pages USER’S MANUAL EPO CONTROL

em3242-reel

EM-3242-T５【Product Specification】 EM-3242-T５【Product Specification】

em-1781_gmw

EM-1781 is ultra-small Hall effect ICs of a single silicon chip composed of Hall element and a signal processing IC.

DTM-133-wGPIB-Manual

DTM-133 DIGITAL TESLAMETER with serial communications USER’S MANUAL

DSSIU-4-1U

Complete 4-channel system interface unit for ultra-stable, high precision fluxgate tech-nology DS series current transducers. Powers up to 4 x DS50 to DS2000 at the same time.

DS-HTS-110-LM

Applications HTS-110’s LM range is suitable for various applications, including: 4 MOKE (Magneto-optic Kerr effect) 4 Magnetic domain imaging 4 Brillouin light scattering 4 Magnetic circular dichroism 4 Hysteresis loop plotting 4 Scanning laser microscopy 4 Hall effect measurements 4 Variable temperature optical cryostat

DS600UB-10V

Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 660A

DS600ID

Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 1000A

DS400ID

Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 600A

DR1481

DQ640ID-B is a current transducer targeting stable power supplies and other areas, where it is important to have the programming flexibility

DR1395

DR1395 MS2 magnetic susceptibility meter MS2 magnetic susceptibility meter

DQ600ID-P1300

Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 1300A

DQ600ID

Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 1000A

DM1200UB-10V

Ultra-stable, high precision (ppm class) fluxgate technology DM Series current transducer for non-intrusive, isolated DC and AC current measurement up to 1320A

DL2000UB-10V

Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 2000A

DL2000ID-CD100

Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 3000A

Datasheet_DC200IF

Highly stabilized and precise fluxgate technology based current transducer, re-engineered for cost sensitive, non-intrusive, isolated DC and AC current measurement applications up to 300A

Data-Acquisition-Units-DS2519

Bartington Instruments’ data acquisition and conditioning units accept analogue inputs from most of our sensors and output the signal in either analogue or digital format, depending on the unit selected.

CZ-3705

CZ-3705 is an open-type current sensor using Hall sensors, which outputs the analog voltage proportional to the AC/DC current. Group III-V semiconductor thin film is used as the Hall sensor, which enables the high-accuracy and high-speed current sensing. Coreless ultra-small surface mount package realizes the space-saving.

CWTUM_accuracy

Positional accuracy and external currents Due to small variations in the winding density and coil cross sectional area the transducer output varies slightly depending on the position of the current in the coil and also the size of the current conductor relative to the coil.

CWT-Power-Cable-YK

CWT / CWT LFR Power Cable compatible with ALL Yokogawa instruments fitted with Probe Power Option

CWTMini-Dimensions

Introducing the NEW CWTMini50HF,an extension of the CWTMiniHF range for even faster transient current measurement

CWT-instructions

PEM?s Rogowski Current Waveform Transducers combine high bandwidth, safety, and the minimum disruption to the circuit under test. These instructions should be followed whenever the unit is used. They are intended to help you obtain the best and safest performance from the transducer

cwt_0318

CWCT & BCM-CW-E CW Current Transformer Beam Charge Monitor for CW beams and Macropulses

CU1-DR3320

Operation Manual for CU1 Helmholtz Coil System Control Unit

CT-04.10.Tech_.note

For personnel and equipment safety and measurement accuracy, current measurements on conductors at high voltage should be made only with a conducting shield cylinder placed inside the CT aperture. There should be a low electrical impedance connection from one end only to a reliable local ground. An inner insulating cylinder of adequate voltage isolation should be between the shield cylinder and the conductor at high voltage. Any leakage, induced or breakdown current between the high voltage conductor and the ground shield will substantially pass to local ground rather than through the signal cable to signal ground. Do not create a "current loop" by connecting the shield cylinder to ground from both ends. Current flowing in this loop will also be measured by the CT.

CS016-metrolab

Like Bartington Instruments, Metrolab Technology SA builds magnetometers.The key difference is that Metrolab’s magnetometers are designed for very strong fields. One of its product lines is a range of three-axis Hall effect magnetometers able to resolve up to 2μT, but even this is insufficient for some purposes. Metrolab has now been able to extend the resolution into the nT range, thanks to Bartington’s Mag649 low-power three-axis fluxgate sensor.

CQ3202

CQ-3302 is an open-type current sensor using a Hall sensor which outputs the analog voltage proportional to the AC/DC current. Quantum well ultra- thin film InAs (Indium Arsenide) is used as the Hall sensor, which enables the high-accuracy and high-speed current sensing. Coreless surface mount package realizes the spacesaving.

CQ3204

CQ-2366 is an open-type current sensor using a Hall sensor which outputs the analog voltage proportional to the AC/DC current. Quantum well ultra-thin film InAs (Indium Arsenide) is used as the Hall sensor, which enables the high-accuracy and high-speed current sensing. Simple AI-Shell package with the Hall sensor,magnetic core, and primary conductor realizes the space-saving and high reliability.

CQ2093

CQ-2093 is an open-type current sensor using a Hall sensor which outputs the analog voltage proportional to the AC/DC current. Quantum well ultra-thin film InAs (Indium Arsenide) is used as the Hall sensor, which enables the high-accuracy and high-speed current sensing. Simple AI-Shell® package with the Hall sensor, magnetic core, and primary conductor realizes the space-saving and high reliability.

CQ2065

CQ-2065 is an open-type current sensor using a Hall sensor which outputs the analog voltage proportional to the AC/DC current. Quantum well ultra-thin film InAs (Indium Arsenide) is used as the Hall sensor, which enables the high-accuracy and high-speed current sensing. Simple AI-Shell® package with the Hall sensor, magnetic core, and primary conductor realizes the space-saving and high reliability.

CQ209x

?? Small-sized surface mount package with magnetic core and current conductor ?? Hybrid Hall IC with semiconductor Hall elements for high sensitivity ?? Current conductor electrically isolated from sensor IC ?? 5V single supply operation ?? Analog output voltage proportional to AC or DC currents ?? Low noise output: 2.1mVrms ?? Fast response time: 1μs to step input current ?? Factory-adjusted sensitivity and offset voltage for high accuracy ?? Flat temperature dependence by compensation circuits ?? Ratiometric output

CPCO-XXXX-160

The CPCO Series (160mm aperture) Current Probes are Clamp On current sensors capable of measuring ac and dc currents. The Current Probe splits along a diameter allowing easy installation to existing cables without having to break the connection. A captive screw is used rather than a clip to ensure consistent closure under mechanical loading or vibration.

BSS-02B outline drawing

BSS-02B outline drawing BSS-02B outline drawing BSS-02B outline drawing

BSS-02B-OM1741

Operation Manual for BSS-02B Magnetic Susceptibility Sonde

BSS-02B-DS0064

The BSS-02B is a borehole probe for measurement of magnetic susceptibility from 10-5 to 10-1 cgs. It is calibrated for use in 50mm diameter boreholes at temperatures up to +90°C, and it is able to operate at depths of up to 6000 metres over a temperature range of ambient to +120°C.

Brochure-PT2026-1.1-US

The world’s most precise magnetometer Metrolab’s PT2026 sets new standards for magnetometers based on NMR (Nuclear Magnetic Resonance), the most precise technique for measuring magnetic flux density. The combination of a pulsed-wave NMR detector and advanced signal processing opens a host of new applications in the areas of magnetic field measurement, monitoring, mapping and calibration.

BPS-85-70_30062017

Clip-on Rogowski current probes provide a convenient and accurate means of measuring alternating currents. The latest wideband probes use an innovative shielding technique to eliminate the effects of high electrostatic field strengths in today’s high power-density and high-speed circuits.

BPs_5-14-PEM

Next-Generation Current Probes for High-Speed and High Power-Density Applications Clip-on Rogowski current probes provide a convenient and accurate means of measuring alternating currents. The latest wideband probes use an innovative shielding technique to eliminate the effects of high electrostatic field strengths in today’s high power-density and high-speed circuits.

BI_MAN_MAG-03PSU-Issue

BARTINGTON MAG-03PSU POWER SUPPLY UNIT OPERATION/MAINTENANCE MANUAL

Bartsoft-Mobile-OM2518

Bartsoft Mobile software acquires, corrects, displays, stores and prints data using Bartington Instruments MS3 meters. This guide explains how to use the software and helps the user understand how it works, including the function of all controls and windows.

AN0036-Fluxgate-magnetometers-used-for-on-board-closed-loop-degaussing

To provide real time data for mitigation of magnetic signatures of ships and submarines.

AN0025-Mag-03-used-to-measure-solar-weather-from-the-ground

To protect communications, power and other technological systems from unusual solar activity by monitoring solar weather from ground stations.

AN0023-Mag-01H-for-compass-safe-distance-testing

Make equipment compliant with international regulations, and to help ensure reliable navigation, by ascertaining the level of interference that the a particular item of equipment causes to a compass.

AN0022-Mag-01H-used-for-Verification-of-Magnetic-Shielding

To measure the effectiveness of magnetic shielding using magnetometer measurements.

AN0021-the-applications-of-the-Bartington-BSS-02B-Sonde

Magnetic susceptibility is an important characteristic of rocks and minerals. It changes according to the materials’ magnetic properties (dia-, para-, ferromagnetic&#823) and will range from negative to highly positive values.

AN0017-Application-of-the-MS2K-Surface-Scanning-Sensor

an issue when measuring the permeability μr of metals using the alternating field of the MS2 or MS3 meter is the effect of sample conductivity. This can give rise to an apparent negative or diamagnetic susceptibility reading.The effect is proportional to the square root of the frequency of measurement and to the shape of the specimen.

AN0001-Applications-of-Single-axis-Fluxgate-Magnetometers

The Magnetic Resonance Imaging (MRI)equipment used in medical physics requires the generation of stable magnetic fields, and is therefore susceptible to interference from external fields. This might be caused by radio frequency interference, lower frequency interference from electrically-operated equipment - such as lifts within the same building - or from electric trains, even at a considerable distance. It is standard practice to survey an area prior to installation of this sensitive equipment to record the variations in the magnetic field, and thereby select a site with the least disturbance, or to establish the level of magnetic shielding required.

AN_133KIT-Spec

The AN_133KIT consists of a EM-3242 angle sensor mounted on a small 0.25 in. square PCB with a 6 in. flat cable. Also included in the kit are three SmCo24 magnets compatible with the angle sensor; a 0.25 in. diameter magnet, a 0.15 in. diameter magnet and a 0.25 in. square magnet. The sensor works well with smaller magnets, but with less air gap. See Reference Design RD101_EM3242 for details.

Ametes_MFS-3A_Spec

The high magnetic field sensitivity, accurate calibration, high stability and high signal output of the Sentron CSA-1V Hall effect IC enable it to be conveniently used to monitor the extended fields from magnetic items and electric equipment.

AKM-Current-Sensor-Parameter-Selection-Chart

AKM Currentier Series of Current Sensing IC's Test Printed Circuit Boards

ak8772_e

●Features ?Precision Bipolar Hall Effect Latch ?Power manageability through "PDN" pin 　Current consumption in Power down mode is less than 1μA ?Low current consumption at active mode : less than avg. 　150μA@VDD=3V ?Ultra small SON package : 1.1×1.4×t0.37mm, Halogen free

ADI-123G-Users-Manual

Precise waveform measurement of long pulses and macropulses up to several milliseconds with minimal droop and noise

ACCT-S-082

Precise waveform measurement of long pulses and macropulses up to several milliseconds with minimal droop and noise.

ACCT-S-016

Precise waveform measurement of long pulses and macropulses up to several milliseconds with minimal droop and noise.

ACCT-manual

Precise waveform measurement of long pulses and macropulses up to several milliseconds with minimal droop and noise.

ACCT-E-RM-3R-dimensions

Precise waveform measurement of long pulses and macropulses up to several milliseconds with minimal droop and noise.

18900480_A_1060-62_Probe_Sample_Location_Range

The 3480 dipole electromagnet is a light weight versatile system that can provide fields approaching 4 Tesla. At 34 kg this magnet can easily be moved between applications and can be operated in any orientation.

18900460_A_1060-62_Probe_Sample_Location

The 3480 dipole electromagnet is a light weight versatile system that can provide fields approaching 4 Tesla. At 34 kg this magnet can easily be moved between applications and can be operated in any orientation.

17900-2210-0-Outline-Dwg

The 3480 dipole electromagnet is a light weight versatile system that can provide fields approaching 4 Tesla. At 34 kg this magnet can easily be moved between applications and can be operated in any orientation.

17900-2209-0-Outline-Drawing

The 3480 dipole electromagnet is a light weight versatile system that can provide fields approaching 4 Tesla. At 34 kg this magnet can easily be moved between applications and can be operated in any orientation.

11907-0363-1_A_Gimbal_Mount_Basic_Dimensions

The 3480 dipole electromagnet is a light weight versatile system that can provide fields approaching 4 Tesla. At 34 kg this magnet can easily be moved between applications and can be operated in any orientation.

11907-0355-0_S1_C_3480_General_Assembly

The 3480 dipole electromagnet is a light weight versatile system that can provide fields approaching 4 Tesla. At 34 kg this magnet can easily be moved between applications and can be operated in any orientation.

5205_Specification

The 5205 electromagnet is a low profile projected vertical field magnet providing uniform Bz field at a location above the magnet surface. It is intended for applications where the space around the working volume needs to be freely accessible.

5203_Specification

The 5203 electromagnet is a projected field magnet providing uniform field at a location above the magnet surface. It is intended for applications where the space around the working volume needs to be freely accessible.

5201 test data hysteresis AC excitation

MODEL: 5201 PROJECTED FIELD ELECTROMAGNET TEST DATA Hysteresis & AC Excitation

3480_17907-0728-0_C_Tapered_Sleeve

The 3480 dipole electromagnet is a light weight versatile system that can provide fields approaching 4 Tesla. At 34 kg this magnet can easily be moved between applications and can be operated in any orientation.

2007 MMM 231HC Presentation

GMW 231HC Bipolar Current Amplifier • True Bipolar: +/-160V, +/-70A. • Enables fast ramping of solid and laminated electromagnets. • With GMW 5403AC laminated electromagnet -2T to +2T ramp time is 0.1 sec or 40T/sec. • USB interface with 16-bit input/output resolution.Current programming.Readback of output current, voltage and magnetic field. • Based on Copley Controls 231HC MRI Gradient Amplifier.

2005-MMM-5201-5403AC-Presentation

Application examples: • In-plane magnetic field effects in magnetic thin film, media and devices. FeRAM, MRAM,MOKE, SMOKE • Scanning Probe Microscopy, SEMPA, STM, ATF. • Calibration and test of Hall effect, MR, GMR sensors • Chemical reaction and biological sample activity study

55C0126

This manual contains all relevant information on the steps, which are necessary to start the 3MTS Teslameter software installation and to operate it properly, once the 3MTS is connected to the PC or Tablet via the delivered USB cable. All files, including the software, user manuals and calibration data have been stored on the 3MTS USB flash memory stick, which is a part of the Teslameter package

55B0082-B

The 3MTS is a handheld Teslameter / Gaussmeter with integrated USB interface. It was developed in cooperation between the two companies SENIS and Matesy.

3MTS_OPMANUAL

The operational safety and functioning of the device can only be guaranteed if both the general safety and accident prevention regulations given by legislator, as well as the safety instructions provided in this Operation Manual are fully considered. We assume no liability for damages caused by the improper use or incorrect device operation.

SPI-Module™ Sputter/Carbon Coater System™

The SPI Supplies Sputter/Carbon coating system allows the flexibility to choose between carbon evaporation and metal sputtering, all in the same system.

Quick and Easy Adaptation of Molecular Biology Technology to Tissue Embedment Polymerization

Using the SPI Cure™ with a standard heating block for 1.5 snap-cap conical tubes, at temperatures from 55–59°C, we have achieved safe and complete polymerization of LR White (acrylic) and SPI Pon (epoxy) resins in both protected and unprotected BEEM® capsules as well as 00-gelatin capsules. Please note that this report concerns a novel3 adaptation of dry-block heating technology designed for molecular biological procedures.In this test, we have purposefully used only resin blanks.Finally, we report that in the case of LR White, no degradation of the material of which the BEEM® capsules are constructed has been observed in either ‘protected’ or ‘unprotected’ heating regimes. We recommend careful testing of embedding molds not specifically mentioned in this paper.

In Situ Probing of IgG Conjugated Gold Nanoparticles in Liquids by SEM and ToFSIMS

We report recent results of in situ observations of IgG conjugated gold nanoparticles in a novel portable vacuum compatible microfluidic device using scanning electron microscope (SEM) and time-of-flight secondary ion mass spectrometry (ToF-SIMS). The unique feature of the liquid flow cell is that the detection window is open to the vacuum allowing direct probing of the liquid surface. The liquid is held within the aperture by the surface tension. The flow cell is composed of a silicon nitride (SiN) membrane and polydimethylsiloxane (PDMS). We have demonstrated that it is fully compatible with vacuum operations for surface analysis. The aperture can be drilled through the 100 nm SiN using a SEM focused ion beam (FIB) or the primary ion beam in ToF-SIMS. Characteristic signals of the conjugated gold nanoparticles were successfully observed through the aperture by both energydispersive X-ray spectroscopy (EDX) in SEM and ToF-SIMS.

SPI-DRY™ Critical Point Dryers

The SPI-DRY line critical point dryers are built rugged and easy to use. Simple manual controls allow for precise control over heating, cooling, and venting rates. From life sciences to aerogels to MEMS applications, the SPI-DRY critical point dryer does it all.

SPI Osmium Plasma Coater

The OPC line of osmium plasma coaters are designed to provide thin, amorphous layers of conductive osmium metal.

05001-2 Silver Con Paint RoHS2

Structure Probe Inc. / SPI Supplies confirms that: 05001-AB, 05002-AB, 05002-GA, 05002P-AB, and 05002-GA Silver Conductive Paint are RoHS2 compliant, fulfilling the definitions and restrictions defined under Directive 2011/65/EC of the European Parliament and of the Council of 21 July 2011.

The SPI Supplies Family of Instruments

Your results will never be better than your sample preparation. See how SPI Supplies can help you deliver the highest quality results for all your SEM/EDS, TEM and FESEM applications.

REBEKA BSE Detector

REBEKA™ combines the best available single crystal scintillators manufactured by Crytur with precise high-vacuum mechanics and readout electronics in one ready-to-use package.

NIST and NPL

NIST and NPL (NIST counterpart in the U.K.) traceable - Certified Reference Material. A Magnification Reference Standard designed for Microscopy by Microscopists.

Apiezon Q Vacuum Sealing Compound Datasheet

Apiezon Sealing Compound Q is a versatile, temporary vacuum sealing medium. It is a soft, putty like substance which is easily moulded by hand at ambient temperatures, yet firm enough to remain in position and is readily removed when no longer required.

Apiezon PFPE 501 MSDS

Apiezon PFPE 501 is a high performance lubricant and sealant which can be used with confidence in extreme environments, ultra high vacuum conditions and in the presence of gaseous and liquid oxygen at elevated temperatures.

美国ARS超稳无液氦低温光学恒温器

• 4-500K温度 • 超低振动 • 超低漂移 • 超高真空兼容 • 选配纳米平移台 • 更大4英寸低温冷台 • 顶部及侧边窗口 • 低噪音测试引线 • 高频及直流测试 • 整体式结构，更方便安装