美国ARS 高效型低温恒温器 X-1SS

镍铬加热器线

 镍铬加热器线（Nichrome heater wire）用来绕制低温加热器。 线径32AWG(0.203mm),成分： 80% 镍（Nickel），20% 铬（Chromium）； Polyimide 绝缘最高操作温度500K。

顺磁共振用低温指状杜瓦

ER 167 FDS-Q Finger dewar For particular, applications, like detection of nitroxide(N0), the nitrogen finger dewar, ER 167 FDS-Q, is the method of choice. The finger dewar minimizes sample preparation time and experimental set-up. The sample temperature is at 77K

碳陶瓷低温温度计

CCS低温温度计 Temati是全球范围内的碳陶瓷低温温度计批发商，碳陶瓷低温温度计在低温温度计量的所有领域都有应用。碳陶瓷温度计发明于1976年，到现在已经有超过10000个碳陶瓷温度计在世界范围内成功应用。

DS-LT3M UHV Flow Cryostat for Manipulation

The ARS manufactured LT3M Helitran is a True UHV cold head (10-11 Torr) where all of the rubber o-ring seals have been replaced with welded joints and metal seals. Like all of our LT3 helium flow cryostats, the LT3M is an advanced liquid helium flow cryostat utilizing many unique features, such as the matrix heat exchanged and the coaxial shield flow transfer line to achieve unparalleled efficiency and ultra low vibration levels. The combination of True UHV and angstrom level vibrations makes the LT3M ideal for low temperature application. The extended length and addition of a rigid support tube allow for cleaving and manipulation.

CryoCon-Users-Guide

The Model 12i / 14i / 18i monitors may be powered by any source providing 7.5 to 48 Volts AC or DC. The IEEE 802.3af Power over Ethernet (PoE) specification is also upported, allowing these units to be powered by its local area network connection. In addition, the Model 18i has eight input channels whereas the Model 14i has four and the Model 12i has two. The instruments are identical in every other way. Each input is independent and is capable of supporting the same wide range of sensor types. Inputs are not scanned or multiplexed.

Model RO-600(1K) – Ruthenium Oxide RTD – RuO Thermometer from Scientific Instruments

The Model RO-600 Ruthenium Oxide Temperature Sensors are thick film resistors which adhere to are available with calibration down to 20mK or grouped/interchangeable and have a nominal resistance of 1,000? at ambient temperature. The ruthenium oxide temperature sensor offers excellent performance characteristics in magnetic field environments. These sensors exhibit an initial small negative magnetoresistance at temperatures below 250 mK at low fields (less than about 1.5 Tesla). The magnetoresistance then becomes positive at larger fields and increases at lower temperatures. This magnetoresistance is repeatable. For example, a resistance change of 8% induced by an 8 Tesla field at a temperature of 80 mK corresponds to a temperature error of 7 mK.

Cryogenic Temperature Multi-Channel Monitor Model 12i / 14i / 18i

The Model 12i / 14i / 18i monitors may be powered by any source providing 7.5 to 48 Volts AC or DC. The IEEE 802.3af Power over Ethernet (PoE) specification is also upported, allowing these units to be powered by its local area network connection. In addition, the Model 18i has eight input channels whereas the Model 14i has four and the Model 12i has two. The instruments are identical in every other way. Each input is independent and is capable of supporting the same wide range of sensor types. Inputs are not scanned or multiplexed.

SCM10 Single Channel Temperature Monitor

SCM10 Single Channel Temperature Monitor The SCM10, single channel temperature monitor, is a compact, reliable instrument capable of providing extremely accurate measurements for a variety of applications. The unit supports diode and RTD sensors and it can be configured for the appropriate sensor type using the front panel or the utility software.

我司在上海某研究所成功进行了美国ARS低温恒温器与Huber设备集成

近日我司在上海某研究所成功进行了美国ARS（ADVANCED RESEARCH SYSTEMS）低温恒温器与Huber设备集成。

VIS-Datasheet-A50-300C

The A50-300C is a high speed driver IC designed for use with electro-optical modulated VCSEL for up to 56 Gbit/s in fiber optic transmission systems. The A50-300C operates from a single +5V supply typically dissipating 380mW of DC power. The device is available as engineering sample.

OPERATION AND MAINTENANCE INSTRUCTIONS

AMI HELIUM VAPOR COOLED CURRENT LEADS AND SUPERCONDUCTING BUS BARS INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS

current_leads

American Magnetics Inc.’s (AMI) Vapor Cooled Current Leads provide reliable and consistent electrical current transfer from room temperature (300K) to a Liquid Helium environment (4.2K). These high efficiency heat exchangers use the heat capacity of cold helium vapor to counterflow the incoming conductive and resistive heat, thereby minimizing the liquid helium consumption. The thermal input of the leads is carefully designed to insure that just enough helium gas is generated to provide adequate cooling across the full range of operating currents. AMI offers a wide range of current lead designs from small current requirements to over 100,000 Ampere leads.

Cryogen_Free_Magnets_Info_Brief

The simplest magnet system is one where a sample insert has a small 6T magnet bolted at the bottom. Such an insert would have an integral variable temperature insert with sample space of 25 mm. These inserts are very effective in performing transport studies on nano size specimens and can be a useful tool to demonstrate the Quantum Hall Effect for educational purposes or for prescreening samples before they are tested at facilities that are not easily accessible.

我司在南京某高校成功安装低温恒温器

近日我司在南京某高校成功安装美国ARS（ADVANCED RESEARCH SYSTEMS）的低温恒温器。

我司在南京某大学低温真空探针台成功维护

近日我司在南京某大学对美国ARS（ADVANCED RESEARCH SYSTEMS）的低温真空探针台成功维护。

我司在深圳某高校成功进行了美国ARS的PS-CC闭循环探针台安装与验收

近日我司在深圳某高校成功进行了美国ARS（ADVANCED RESEARCH SYSTEMS）的PS-CC闭循环探针台安装与验收

RMP Flyer German / English

Der RMP Rotormessplatz ist ein universelles Messsystem zur Erfassung der Eigenschaften von Permanentmagnet-Rotoren. Steuerbare Achsen, eine präzise Mechanik und kalibrierte 1- bzw. 3-achsige Hall-Sensoren bis zu 1 Tesla zeichnen den RMP aus.

layer-tester Flyer German

Der Layer Tester wurde entwickelt, um die jeweiligen Beschichtungen auf Floatglas zu unterscheiden. Das Gerät arbeitet mit zwei verschiedenen Widerstandwerten und erkennt so sicher und schnell, welche Beschichtung auf das Glas aufgebracht wurde. Der Layer Tester ist Batteriebetrieben und intuitiv in der Anwendung. Sobald die in das Prüfgerät integrierten Kontaktspitzen mit dem Prüfglas in Berührung kommen, wird über zwei LEDs das Messergebnis angezeigt. Unterschieden wird dabei zwischen den beiden Flächenwiderstandsbereichen 0 bis 15 ?sq (low resistance) und 22 bis 60 ?sq (high resistance).

Helmholtz Spulen Flyer German

Eine von Matesy’s Kernkompetenzen ist die Abwicklung von Entwicklungsprojekten. Mit Ihnen gemeinsam erarbeiten wir einen konkreten Lösungsansatz, fertigen ein System anhand Ihrer Bedürfnisse und unterstützen Sie bei der Implementierung.

m-axis Flyer English

m-axis is a measurement system to investigate the magnetic specifications of permanent magnets (magnetization angle and magnetic moment). Due to the modular setup it is possible to customize the measurement range of the m-axis system in addition to the four standard ranges and for 100% quality control.

HVG

低温用道康宁真空脂 特性 • 良好的润滑性能和密封性能 • 低挥发性 • 优良的耐水性、耐化学品性能及耐高温和低温性能 组成 • 硅油 • 增稠剂 应用 • 化工设备的密封和润滑油脂 • 用于活塞阀、控制阀、流量计轴承、陶瓷活塞阀、灭火器阀门、水设备阀门、合成橡胶垫圈及密封圈在高温下使用时的润滑 • 真空和压力系统的密封用润滑油脂 • 用于双筒望远镜中O型环的润滑，防止精密镜头起雾

ScanningTunnelMicroscopy

Scanning Tunnel Microscopy (STM) is the earliest technique that was developed in the scanning probe microscopy (SPM) area. It generates imaging surfaces with atomic resolution, which is ~ 0.1 nm in lateral and ~ 0.01 nm in depth. The principle of the STM is based on quantum tunneling. When conducting measurements,a conducting sharp tip as the probe is brought very close to the surface. In the meantime, a voltage bias is applied between the tip and sample to make electrons tunnel through space. The resulting image is the change in the tip height as the tip is scanned over the sample surface. Clean sample surface and tip, and low electronic and physical noise are required for high-resolution STM imaging. The STM can be widely used in UHV or any other gas or liquid ambients from the temperature of ~ 0K up to 1300K.

Time-DomainThermoreflectance时域热反射测量法(TDTR)

时域热反射测量法(TDTR)是测量各种块状和薄膜材料及其界面热导率的最有效方法之一。其原理是利用表面反射率的变化来推导材料被加热时的热特性。该装置包括一个泵和探针脉冲激光器。利用泵浦激 光器产生声脉冲。声波脉冲可以在界面处处于透射或反射状态，这取决于界面的属性。探针激光通过光电探测器探测反射的声脉冲。从而可以测量反射率随时间的变化，并且通过匹配理论模型来提取热特性。对温度依赖的TDTR 可以借助低温恒温器来研究电子和声子等载流子输运过程的基本物理。

RamanScattering拉曼散射

拉曼光谱是一种检测晶格或分子振动或旋转模式的技术。有两种类型的散射，瑞利散射和拉曼散射。瑞利散射是弹性的，拉曼散射是非弹性的。当拉曼散射发生时，入射光子和散射光子之间存在能量差异。拉曼光谱显示出这种能量差异，它与晶格或分子的特定振动或转动模式相对应。因此，常用来识别和分析样品的结构和组成。它还可以与显微镜结合来观察单个纳米结构或称为微拉曼光谱的微观区域。

Photoluminescence

Photoluminescence (PL) spectroscopy is a widely used technique for the characterization of the optical and electronic properties of semiconductors and molecules. PL is a process of light emission from any form of matter after the absorption of photons. The incident photon in the visible region excites one of its electrons to the excited state. And then, it radiates a photon as the electron return to the lower energy state. In quantum mechanics, the energy band is quantized, which means only certain transitions are allowed. Therefore, the discontinued energy peaks of luminescence are expected.

MatrixIsolation基质隔离

基质分离是一种光谱研究，旨在将材料(客体粒子)置于极低温的惰性介质(宿主基质)中。它的出现是基于瞬态分子的高化学反应性，很难获得气相红外光谱。客体粒子和主基质的混合物沉积在一个透明窗口上，该窗口将被冷却到熔点以下。所以实验必须在高真空下进行，以防止有害气体中的污染物冻结到冷窗上。

Fourier-TransformInfraredSpectroscopy(FTIR)傅立叶变换红外吸收光谱学

当样品暴露在红外辐射下时，通过吸收特定波长的辐射激发偶极矩。振动能量将从基态激发到激发态。与色散光谱学不同，傅立叶变换红外外吸收光谱（FTIR）同时包含多个光频率并测量吸收。接下来，光束包含不同频率的光并重复它。重复几次后，原始数据将被处理为结果数据cm-1，wavenumber。这个过程称为傅立叶变换。

Ellipsometry

Ellipsometry is an optical method to derive the dielectric properties of thin films. Polarized incident light is reflected obliquely from the surface of the sample to generate ellipse of polarization reflected light in terms of amplitude ratio and phase difference, which is measured by a spectroscopic ellipsometer. Information about composition, roughness, thickness, doping concentration and other material characters can be yielded through it. Intrinsic physical properties of thin films can also be studied by the temperature dependence of ellipsometry.

Deep-LevelTransientSpectroscopy(DLTS)

Deep-level transient spectroscopy (DLTS) is a very powerful tool to detect the defect concentration and thermal emission rate of semiconductor deep levels by measuring capacitance transients as a function of temperature. It normally used the Schottky diode or p-n junction as a probe. In the process, the probe is forward biased to fill the defects with free carriers by a pulse voltage. After the pulse, the defects start emitting trapped carriers due to thermal emission.

Deep-LevelTransientSpectroscopy(DLTS)深能级瞬态谱

深能级瞬态光谱（DLTS）是通过测量电容瞬态随温度变化来检测半导体深能级缺陷浓度和热发射速率的有力工具。它通常使用肖特基二极管或p-n 结作为探针。在此过程中，探针正向偏压，以脉冲电压填充自由载流子缺陷。脉冲后，由于热发射，缺陷开始发射捕获载流子。

Angle-ResolvedPhotoemissionSpectroscopy(ARPES)

Angle-Resolved Photoemission Spectroscopy (ARPES) is one type of photoemission spectroscopies to obtain information about the electronic band structure and Fermi surface of crystals in the reciprocal space. Soft X-ray is irradiated onto the crystal surface, and the kinetic energy of photoelectrons emitted from the surface is measured as a function of polar and azimuthal angles. Because electrons escape from the surface are projected through the surface, the direction of the momentum perpendicular to the surface is not conserved. Therefore, ARPES is an ideal tool for 2D materials because the direction of the electronic momentum of interest is parallel to the surface. The increased sensitivity of excitations can be achieved by reducing thermal energy at cryogenic temperatures.

DiamondAnvilCell金刚石压砧

金刚石顶砧（DAC）是一种实验性的元件，它通过用两个相对的金刚石压缩一小块材料来产生极端压力。压力通常可达100-200 GPa。这项技术的目标是模拟行星内部的环境来合成材料并观察在正常大气环境下不会发生的相位。样品可以通过钻石观察，也可以进行光学测量，如X 射线衍射、穆斯堡尔谱和光致发光。通常，样品可通过电阻加热至1000°C 或激光加热至5700°C 进行加热。DAC 实验也可在低温下进行，DAC 实验也可以根据不同的目的在低温下进行。

ThermoelectricEffect

The thermoelectric effect is the relationship between thermal and electric. When a temperature difference is created on both sides of the device, carriers in material diffuse from the hot side to the cold side, which results in a voltage across the device. Conversely, when a voltage is applied, heat is transferred from one side to the other, a temperature gradient is created. The thermoelectric effect generally consists of three effects, Seebeck effect, Peltier effect, and Thomason effect.

Magnetotransport磁输运

当量子材料特别是二维材料或多层材料在低温电子输运过程中受到磁场的作用时，需要考虑电子的运动轨迹和电子的自旋。量子霍尔效应是霍尔效应的一种量子力学形式。它经常被用来表征具有磁电阻的现代量子材料。磁电阻是样品在磁场作用下电阻发生变化的现象。当样品中含有铁磁性金属时，样品的磁化强度和自旋极化电流的相互作用。电阻可以通过各种物理现象产生的磁电阻效应来实现，如巨磁电阻效应和隧道磁电阻效应，从而引出自旋电子学的研究课题。

ElectronTransport

In classical physics, when an electric potential is applied through a bulk of metal or semiconductor, carriers will be driven. The electrical resistance can be obtained by Ohm’s law. This effect is called electron transport. This is one of the most common techniques to characterize materials. Many of the phenomena can be observed through this echnique, such as electrical conductivity, electron mobility.

IonTrap

Ion trap is a scientific technique to confine ions/charged particles in a small region of space through magnetic or/and electric fields. Many studies are carried out on the ion trap method, such as optical spectroscopic properties of the captured ion and mass spectrometric properties of fragment ions.

Parahydrogen仲氢

仲氢是氢(H2)的两种磁性形式之一。它通常用于提高核磁共振和核磁共振测量的灵敏度。 氢分子由两个原子组成。每个原子都有一个旋转的原子核。根据核自旋的方向，氢原子有两种类型。 如果两个氢原子原子核的自旋是平行的，那它就是正氢。如果自旋是反平行的，它就是仲氢。一般来说，氢气是正氢和仲氢的平衡混合物。这两种磁态之间有微小的能量差。

NobleGasAnalysis惰性气体分析

惰性气体，也就是氦(He)、氖(Ne)、氩(Ar)、氪(Kr)、氙(Xe)形成了一组性质相似的化学元素，如无味、无色和单原子。最重要的是，它们在化学上不发生反应。因此，它们也被称为惰性气体。由于惰性气体的化学和生物惰性以及放射性衰变所产生的独特同位素特征，惰性气体通常被用于探测海洋和地球过程，例如岩石和矿物年代测定。

NeutronScattering中子散射

中子散射技术利用中子散射方法研究物质的静态结构及物质的微观动力学性质。中子具备不带电、穿透力强、可鉴别同位素、较之X 射线对轻元素灵敏、具有磁矩等优点，因此中子散射技术作为一种独特的、从原子和分子尺度上研究物质结构和动态特性的表征手段，在多学科交叉领域发挥着不可替代的作用。

Viewport Glass Components

Low Profile — Low profile high transmission glass viewports available with 0.56 to 2.69 view diameters. Wide Range — Sapphire, fused silica, Accu-Sol™ and 7056 borosilicate glass substrate types offer a wide range of transmission options. Demountable Substrate — Unique “demountable” viewport design available to allow end users the option of having the viewport coated. This demountable design also allows for ease of cleaning and/or replacement.

我司在西安某高校成功进行了美国ARS低温恒温器与Horiba光谱仪耦合

近日我司在西安某高校成功进行了美国ARS （ADVANCED RESEARCH SYSTEMS）低温恒温器与Horiba光谱仪耦合。

Breaks Fluid Feedthroughs

Vacuum Breaks — excellent voltage isolation in both UHV and HV environments.Constructed using high purity alumina ceramic sealed to stainless sleeve adapters. Water, Fluid Breaks — voltage isolation in water or coolant fluid lines. Soldering or brazing requires low temperatures below 700°C. Standard adapters fit 1/4 to 1/2 Inch diameter tubes. Cryogenic, Fluid Breaks — great voltage isolation for cryogenic fluid lines. Designed to be TIG welded into cryogenic fluid transmission lines with 1/8 to 3/8 Inch diameters.Allows safe operation to –200°C.

LT3B超高真空连续流低温恒温器

LT3B超高真空连续流低温恒温器应用十分广泛，拥有很多独特特点，如热交换型液氦传输管线可以提高制冷效率而且极大的消除振动。

X-19-NO非光学低温恒温器

X-19-NO是顶端装载样品的非光学型恒温器，样品置于氦气交换气体腔，使用样品杆更换样品，换样时无需关闭制冷机，这样的设计换样速度快，特别适合需要进行大量样品测试情况。而且样品置于冷的氦气环境中，适用于各种导热性不好的样品降温。

LT4连续流低温恒温器

LT4系列连续流恒温器是经济连续流恒温器，可进行光电磁各种低温测试。 LT4既可以使用液氦也可以使用液氮进行工作。该系统包含标准的传输管线和冷指，也可根据客户需要进行定制。

ARS水冷机

美国ARS 水冷机   标准电压  频率 60 Hz 50 Hz 最小 200 V 200 V 最大 230 V 230 V 制冷量 3.9 kW 3.9 kW

我司在香港浸会大学顺利完成美国ARS高低温超宽温区低温恒温器验收工作

近日我司在香港浸会大学顺利完成美国ARS（ADVANCED RESEARCH SYSTEMS）高低温超宽温区低温恒温器验收工作，该款低温恒温器为完全无液氦系统，温度测试范围从10K-800K，为客户的光电测试提供了超宽的温区操作，是宽量程测试的首选。

X-1SS高效型低温恒温器

X-1SS高效型低温恒温器拥有不锈钢真空外罩及仪表群。配以合适的真空系统该套恒温器真空度可达10-7 Torr，更高的真空度会有效防止样品表面污染。 镍镀金无氧铜铜防热辐射屏耐用，热辐射低，是低温实验下理想的防热辐射材料。 X-1SS系列恒温器可配备DE-202、DE-204或DE-210系列冷头，根据客户需要可选择4K，5.5K，10K不同型号。

ds.MG80.Cooler

Typical Applications • LN2 Replacement • IR Laser Diode Cooling • CCD Detectors • Raman Detectors • Infrared Detectors • Mobile Communications • Cold traps • Optics • Electronics (LNAs, HTS, CMOS, Etc.)

ds.LC1-x1

Liquid Nitrogen Pour Fill: Inexpensive cryostat for short term experiments at 77K and 77K to 200K range with the high temperature interface.

ds.cs210-x21

Applications: High Cooling power for: Low Vibration Optical Experiments Quantum Dot – Photoluminescence, MicroRaman, Micro PL. Microspectroscopy. Kerr Effect (MOKE), Ellisometry

ds.cs210-x5

Closed Cycle Cryostat for Neutron Scattering Experiments. The CS-210 is a high power cooler with fast cooldown and high cooling power.

ds.cc210

Unique Features: • Cooling power on first stage is higher than comparable systems for cooling larger radiation and other parasitic heat loads for magnet cooling. • Pneumatic Drive Displex Cryocooler for low vibrations at the sample (see Specifications). • Only two moving/Wearing components for high reliability. • Displacer can be removed from the cryocooler for maintainence in the field without breaking vacuum. • Tunable for high performance at any heat load. • Easy field maintenance. Low life cycle cost. • Compressor Model ARS-10HW is water cooled for quiet and clean operation. • Low cooling water flow rate.

ds.cc202

The ARS Pneumatic Drive Cryocooler is a two component closed cycle system operating in the temperature range 3K to 300K. It has no mechanical drive linkages making it very low maintenance and reliable. The displacer motion is controlled by the differential gas pressure, this results in low vibrations at the second stage of the cryocooler.

ds.windowmaterials

Optical specifications of window materials. ARS cryostats are available with a large selection of optical windows for UV, Vis and IR experiments. UV - .1 to .3 Microns (100 - 300 Nanometers) VIS - .3 to 1 Microns (300 to 1000 Nanometers) IR - 1 + Microns ( 1000 nanometers)

ds.Compressors

Safety Features: • Internal breaker switch with indicator light. • High temperature switch with red (over temperature) indicator light on front panel. • Over current switch, automatically resets.For voltage spikes. • Fused protection for low voltage circuits

ds opn 500 800k

This interface allows the cryocooler to operate up to 800K. Except as indicated in low power coolers such as DE-202 with 50 Hz power supply. The maximum and minimum temperature ratings of the cryocoolers is shown in table below.

AutomatedSystemFlier

? Complete Turn-Key Operation ? Easy to Use ? State-of–the-Art Remote Control ? Real-Time Dynamic System Status ? Materials Property Testing: Optical, Electrical, Magnetic

DS-PSW-10-4

This model of the ARS Probe Station is designed for the ultimate in flexibility for non-destructive device testing. The ability to upgrade and modify this system for further device testing has been in the forefront of this design.

DS-superconducting-magnet-probe-station

The ARS Closed Cycle Superconducting Magnet probe station model is designed for the ultimate in flexibility for non-destructive device testing. This system enhanced with a 3T Vertical superconducting Magnetic Field. Those systems are ideal for the study of magneto-optical and magneto-electrical properties in variety of experiments, including quan-tum dots, spintronic devices and nanoscale electronics. The probe con-figuration and system design can be customized to suit your specific experimental requirements.

DS-CS204AF-DMX-20-OM

The DE204*F-DMX-20-OM is our Ultra Low Vibration Closed Cycle Cryostat for Optical Micrscopy applications such as MicroRaman and Micro Photoluminescence. The DE204*F-DMX-20-OM uses a Helium Exchange Gas to decouple the sample from the cold tip of the DE204 Cryocooler. This pre-vents almost all vibration from being transmitted to the sample. Sample vibrations of 3-5 nm have been demonstrated by users. Due to the exchange gas being less conductive, the base temperature will increase by 4-5K and the cooling capacity is roughly cut in half at varying temperatures.

DS-CS210AF-GMX-20B

The CS210*F-GMX-20B opens up a wide range of possibilities never before possible with a closed cycle cryocooler. The ARS manufactured DMX-20B interface, like our “B” series cold heads is a True UHV System (10-11 Torr) where all of the rubber o-ring seals have been replaced with welded joings and metal seals. A CF flange is The DE210*F-GMX-20B uses a Helium Exchange Gas to decouple the sample from the cold tip of the DE210 Cryocooler. This prevents almost all vibration from being transmitted to the sample. Due to the exchange gas being less conductive, the base temperature will increase by ~1K and the cooling capacity is roughly cut in half at varying temperatures.

DS-CS210AE-GMX-1SS

The CS210*E-GMX-1SS offers very high cooling power for fast cool downs and low base temperatures. This system is ideal when characterizing large materials with high heat loads or when the lowest possible temperature wants to be achieved. The system is capable of vacuum levels of 10-7 Torr with an appropriate vacuum pump. The lower vacuum reduces the sample surface contamination such as water molecules, which can be particularly detrimental to IR Spectroscopy.

DS-CS204AI-FMX-1SS

The CS204*I-FMX-1SS is our standard intermediate cooling power cryostat for optical and electri-cal measurements. This high performance system offers and all stainless steel constructed vacu-um shroud along with a welded stainless steel instrumentation skirt. This system is capable of achieving vacuum levels of 10-7 Torr with an appropriate vacuum system.

DS-CS202AI-DMX-1SS

The CS202*I-DMX-1SS is a high performance closed cycle cryostat for Optical, Electrical, and Magnetic sample testing. It has an all stainless steel vacuum shroud along with a welded stainless steel instrumentation skirt. The system is capable of vacuum levels of 10-7 Torr with an appropriate vacuum pump.

DS-LT3-WMX-1SS

The LT3-WMX-1SS offers a wide range of flexibility at a reasonable cost. This high performance systems offers an all stainless steel constructed vacuum shroud along with a welded stainless steel instrumentation skirt. This system is capable of achieving vacuum levels of 10-7 Torr with an appropriate vacuum system. The nickel plated copper radiation shield provides low emissivity which is ideal for low temperature experiments.

低温SPM(扫描探针显微镜)解决方案

使用RHK 公司提供的PanScan 自由STM(扫描隧道显微镜) 系统结合ARS DMX-20B 产品的可实现8K 温度下的原子级分辨率。

AirDryAgSelectorGuide

DuPont Conductive Silver Compositions for General Purpose Air-Dry Applications

GlassCoatedWire玻璃包丝（镀玻璃线材玻璃涂层电学测试线缆）

美国GW Lab 一直致力于设计、开发和制造尺寸介于单微米和数百微米之间的玻璃涂层电学测试线缆。GW Lab 专门为客户的特殊需求定制电线和电线组件。固体玻璃独特的绝缘性使我们能够为各种高科技行业制造广泛的电子元件。我们成熟技术使得我们可以为客户研发新的线缆，即使是少量的。从研发到生产，我们在产品的各个阶段都为客户提供技术和销售方面的支持。

NEWT-Litz-Book

Litz wire consists of a number of individually insulated magnet wires twisted or braided into a uniform pattern with the primary benefit of reducing AC losses in high frequency windings. New England Wire Technologies offers unlimited Litz wire constructions with multiple types of insulation to meet agency and/or specific customer voltage withstand requirements.

NEWT Overview

As a leading producer of high-quality braided products, New England Wire Technologies designs and manufactures flat-wire braiding, braid-reinforced tubing, scope braids and insulated braids. Our products are used for applications such as ground strap, motor brush leads, circuit breaker shunts, flexible bus bar, RFI/EMI shielding and shielding for mechanical protection of single or multi-conductor cables. We also create flexible cables and strands for use as flexible conductors in custom single and multiconductor insulated cables.

美国GMW-hw-322b_gmw

Please be aware that AKE products are not intended for use in life support equipment, devices, or systems. Use of AKE products in such applications requires the advance written approval of the appropriate AKE officer. Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks,adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of AKE products in such applications is understood to be fully at the risk of the customer using AKE devices or systems.

美国GMW-hw-300b_gmw

Please be aware that our products are not intended for use in life support equipment, devices, or systems. Use of our products in such applications requires the advance written approval of our sales staff. Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks, adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of our products in such applications is understood to be fully at the risk of the customer using our devices or systems.

美国GMW-hw-108a_gmw

Please be aware that our products are not intended for use in life support equipment, devices, or systems. Use of our products in such applications requires the advance written approval of our sales staff.Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks,adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of our products in such applications is understood to be fully at the risk of the customer using our devices or systems.

美国GMW-hw-105c_gmw

Please be aware that our products are not intended for use in life support equipment, devices, or systems. Use of our products in such applications requires the advance written approval of our sales staff.Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks,adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of our products in such applications is understood to be fully at the risk of the customer using our devices or systems.

美国GMW-hw-105a_gmw

Please be aware that our products are not intended for use in life support equipment, devices, or systems. Use of our products in such applications requires the advance written approval of our sales staff. Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks, adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of our products in such applications is understood to be fully at the risk of the customer using our devices or systems.

美国GMW-hw-101a-4t_gmw

Please be aware that our products are not intended for use in life support equipment, devices, or systems. Use of our products in such applications requires the advance written approval of our sales staff. Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks,adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of our products in such applications is understood to be fully at the risk of the customer using our devices or systems.

美国GMW-hs-0111_gmw

Please be aware that our products are not intended for use in life support equipment, devices, or systems. Use of our products in such applications requires the advance written approval of our sales staff.Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks,adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of our products in such applications is understood to be fully at the risk of the customer using our devices or systems.

美国GMW-hq-8220_gmw

•Please be aware that our products are not intended for use in life support equipment, devices, or systems. Use of our products in such applications requires the advance written approval of our sales staff. Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks,adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of our products in such applications is understood to be fully at the risk of the customer using our devices or systems. •Handling precautions required for preventing electrostatic discharge. •This product contains galium arsenide（GaAs）.Handling and discarding precautions required.

美国GMW-hq-0811_e

HQ-0811 HQ-0811は超小型SON形状量子井戸型InAsホール 素子です。 標準はテーピングリール供給です。（5000pcs./Reel） 注意：弊社製品のご検討にあたっては本カタログの表紙裏の「重要注意事項」を 良くお読み下さい。

美国GMW-hq-0222_gmw

Please be aware that our products are not intended for use in life support equipment, devices, or systems. Use of our products in such applications requires the advance written approval of our sales staff. Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks, adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of our products in such applications is understood to be fully at the risk of the customer using our devices or systems.

美国GMW-hq-0221_gmw

•Please be aware that our products are not intended for use in life support equipment, devices, or systems. Use of our products in such applications requires the advance written approval of our sales staff. Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks, adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of our products in such applications is understood to be fully at the risk of the customer using our devices or systems. •Handling precautions required for preventing electrostatic discharge. •This product contains galium arsenide（GaAs）.Handling and discarding precautions required.

美国GMW-hg-0814_e

•Please be aware that our products are not intended for use in life support equipment, devices, or systems. Use of our products in such applications requires the advance written approval of our sales staff. Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks,adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of our products in such applications is understood to be fully at the risk of the customer using our devices or systems. •Handling precautions required for preventing electrostatic discharge. •This product contains galium arsenide（GaAs）.Handling and discarding precautions required.

美国GMW-hg-0813_e

•Please be aware that our products are not intended for use in life support equipment, devices, or systems. Use of our products in such applications requires the advance written approval of our sales staff. Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks,adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of our products in such applications is understood to be fully at the risk of the customer using our devices or systems. •Handling precautions required for preventing electrostatic discharge. •This product contains galium arsenide（GaAs）.Handling and discarding precautions required.

美国GMW-HG-0715

HG-0715 HG-0715は、超小型SON形状GaAsホール素子です。 標準はテーピングリール供給です。（10,000pcs.／Reel） 注意： 弊社製品のご検討にあたっては本カタログの表紙裏の「重要注意事項」を 良くお読みください。

美国GMW-HG-0713

HG-0713 HG-0713は、超小型SON形状GaAsホール素子です。 定電流駆動時HG-0712より高感度になります。 標準はテーピングリール供給です。（10,000pcs.／Reel） 注意： 弊社製品のご検討にあたっては本カタログの表紙裏の「重要注意事項」を 良くお読みください。

美国GMW-hg-372a_gmw

•Please be aware that our products are not intended for use in life support equipment, devices, or systems. Use of our products in such applications requires the advance written approval of our sales staff. Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks,adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of our products in such applications is understood to be fully at the risk of the customer using our devices or systems. •Handling precautions required for preventing electrostatic discharge. •This product contains galium arsenide（GaAs）.Handling and discarding precautions required.

美国GMW-hg-302c_e

•Please be aware that our products are not intended for use in life support equipment, devices, or systems. Use of our products in such applications requires the advance written approval of our sales staff. Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks, adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of our products in such applications is understood to be fully at the risk of the customer using our devices or systems. •Handling precautions required for preventing electrostatic discharge. •This product contains galium arsenide（GaAs）.Handling and discarding precautions required.

美国GMW-hg-302a_gmw

•Please be aware that our products are not intended for use in life support equipment, devices, or systems. Use of our products in such applications requires the advance written approval of our sales staff.Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks,adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of our products in such applications is understood to be fully at the risk of the customer using our devices or systems. •Handling precautions required for preventing electrostatic discharge. •This product contains galium arsenide（GaAs）.Handling and discarding precautions required.

美国GMW-hg-186a_gmw

•Please be aware that AKE products are not intended for use in life support equipment, devices, or systems. Use of AKE products in such applications requires the advance written approval of the appropriate AKE officer.Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks,adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of AKE products in such applications is understood to be fully at the risk of the customer using AKE devices or systems. •Handling precautions required for preventing electrostatic discharge. •This product contains galium arsenide（GaAs）.Handling and discarding precautions required.

美国GMW-hg-166a-2u_gmw

•Please be aware that AKE products are not intended for use in life support equipment, devices, or systems. Use of AKE products in such applications requires the advance written approval of the appropriate AKE officer.Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks,adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of AKE products in such applications is understood to be fully at the risk of the customer using AKE devices or systems. •Handling precautions required for preventing electrostatic discharge. •This product contains galium arsenide（GaAs）.Handling and discarding precautions required.

美国GMW-hg-166a_gmw

AKEMD assumes no liability for infringement of any patent, intellectual property, or other rights in the application or use of any information contained herein.

美国GMW-hg-116c_e

These products and their specifications are subject to change without notice. When you consider any use or application of these products, please make inquiries the sales office of Asahi Kasei Microdevices Corporation (AKM) or authorized distributors as to current status of the products.

美国GMW-hg-116a_e

Handling precautions required for preventing electrostatic discharge

美国GMW-hg-106c-2u_gmw

Please be aware that AKE products are not intended for use in life support equipment, devices, or systems. Use of AKE products in such applications requires the advance written approval of the appropriate AKE officer. Certain applications using semiconductor devices may involve potential risks of personal injury, property damage, or loss of life. In order to minimize these risks, adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of AKE products in such applications is understood to be fully at the risk of the customer using AKE devices or systems.

美国GMW-AN_180KIT-AKM-HG-106C-2U

The AN_180KIT takes advantage of the very special lead frame and size of the AKM HG-106C-2U, GaAs, Hall element to detail the method of making a very thin (<0.65mm) thick, high field (+/-1T) magnetic field sensor.The kit incorporates a thin 0.4mm thick PCB and includes all the circuitry to interface with the Hall element. For the most temperature stable output, the HG series Halls should be driven with a constant current source. This kit has a current source of 0.5mA and an instrument amplifier to increase the Hall element output signal to a full scale analog voltage of 2.5V +/- 1.5V for a magnetic field up to +/-1.5T. The output is linear to a magnetic field of +/-1T.

美国GMW-AN_160

The AN_160KIT is a Universal Hall Interface Module (UHIM) which provides an easy means to evaluate the Asahi Hall elements for magnetic field, electric current or position sensing applications.The UHIM consists of a differential amplifier, a voltage drive circuit for Hall elements requiring a voltage drive, a current drive circuit for Hall elements requiring current drive, and two analog output circuits to provide the standard 2.5V ±2.5V signal and a 1.5V ±1.5V signal for 0-3V input level A/D circuits.

美国GMW-AKM-RoHS_Statement

The Current Sensor Modules use a Hybrid Hall IC, which includes: a high sensitivity Hall element, an amplifier, a buffer, compensation circuitry, and a drive circuit for the Hall sensor. CQ206x and CQ209x Series also include an EEPROM unit providing factory-adjusted sensitivity and offset voltage for high accuracy. The compensation circuitry provides flat temperature dependence. The current conductor is electrically isolated from the sensor IC. The output is linear and ratiometric to the supply voltage.

美国GMW-AKM_2011_Sensors_PG_GMW

A Hall Element is a magneto-electric transducer which utilizes the Hall Effect to measure or sense a magnetic field perpendicular to the Element. AKM Hall Elements typically have 4 pins, 2 input pins and 2 output pins, and can be driven by either a voltage or a current source. The output is a Hall voltage that is proportional to the magnetic field. The output from a Hall Element is analog and typically requires additional amplification. AKM uses four different semiconductor materials in its Hall Elements. These different materials represent AKM’s 4 different series of part numbers. The different materials provide different performance characteristics (magnetic sensitivity represented by electron mobility and band gap, operating voltage, temperature sensitivity, etc.) allowing the design engineer to choose the best solution for the particular application.

Wada-FCT

For any experiments that use beams of an accelerator,monitoring the beam intensity is always an important concern. It is particularly useful if one can continuously measure the beam current without disturbing the beams. Counting elastic scattering particle from the target is often used for such a purpose,however, the dynamic range of measurable beam intensity is limited and the calibration often changes for different experimental conditions.

VWM-S-1W-A60mm-TopView

VWM-S-1W-A60mm-TopView VWM-S-1W-A60mm-TopView VWM-S-1W-A60mm-TopView

VWM-S-1W-A40mm-TopView

VWM-S-1W-A40mm-TopView VWM-S-1W-A40mm-TopView VWM-S-1W-A40mm-TopView

VWM-S-1W-A40mm-MainView

VWM-S-1W-A40mm-MainView VWM-S-1W-A40mm-MainView VWM-S-1W-A40mm-MainView

VWM-S-1W-A40mm-FrontView

VWM-S-1W-A40mm-FrontView VWM-S-1W-A40mm-FrontView VWM-S-1W-A40mm-FrontView

VWM-S-1W-A20mm-MainView

VWM-S-1W-A20mm-MainView VWM-S-1W-A20mm-MainView VWM-S-1W-A20mm-MainView

VWM-S-1W-A5mm-RightView

VWM-S-1W-A5mm-RightView VWM-S-1W-A5mm-RightView VWM-S-1W-A5mm-RightView

VWM-S-1W-A5mm-MainView

VWM-S-1W-A5mm-MainView VWM-S-1W-A5mm-MainView VWM-S-1W-A5mm-MainView

VWM-Manual-VWM005

This document refers to the VMW-005 5-wire Vibrating Wire Monitor delivered to Argonne National Laboratory in 2007 to measure the profile of photon beams on the Advanced Light Source. The APS scientist who evaluated it is Glenn Decker.

VSM-paper-accepted

A simple Vibrating Sample Magnetometer for macroscopic samples

VAC-DS-4644-X054

700 A - Stromsensor Modul / Current Sensor Module (Molex Connector)

VAC-DS-4644-X052

500 A - Stromsensor Modul / Current Sensor Module (Molex Connector)

VAC-BR-Stromsensor

This brochure covers the standard current sensor range of VACUUMSCHMELZE GmbH & Co. KG (VAC) for the floating measurement of currents. Customized solutions are available on request.

VAC-4640-X152

1000 A Current Sensor for ±24V- Supply Voltage for electric current measurement: DC, AC, pulsed, mixed ..., with a galvanic isolation between primary circuit (high power) and secondary circuit (electronic circuit)

US-Danisense-Product-Naming-Price-List-2018-letter

Since our establishment in November 2012, Danisense’s philosophy has always been to provide you the best in everything we do. In return, the market feedback has been so good. Our growth has constantly exceeded expectation. In the past several years, we’ve continuously released new products to broaden our offering.

Turbo-ICT-manual

Turbo-ICT & BCM-RF-E Turbo Integrating Current Transformer Beam Charge Monitor – RF Electronics User’s Manual

TNC-Cable-DR0645

TNC-Cable-DR0645 TNC-Cable-DR0645 TNC-Cable-DR0645

The-Parametric-Current-Transformer

Toroidal transformers are used to measure the beam current in beam lines and accelerators. Placing such a transformer hi the feedback loop of an operational amplifier will increase the useful frequency range (active current transformer). A magnetic modulator can be added to extend the response to DC current, maintaining with a control loop the transformer core at a zero flux state.

Spectramag-6-OM2021

Operation Manual for Spectramag-6 Six-Channel Spectrum Analyser for Magnetic Field, Vibration and LF Acoustics SOFTWARE VERSION 6.203

Spacemag-Lite_DS2714

Bartington Instruments offers a fluxgate magnetometer for spaceflight applications. Spacemag-Lite® is ideal for a variety of low Earth orbit (LEO) missions, including commercial and scientific missions, where cost is a consideration.

SOR-MAN-SGA

AMETEK, Inc. is a leading global manufacturer of electronic instruments and electromechanical devices with annualized sales of $2.5 billion. The Company has over 11,000 colleagues working at more than 80 manufacturing facilities and more than 80 sales and service centers in the United States and around the world.

SOR-MAN-DLM600

AMETEK Programmable Power, Inc., a Division of AMETEK, Inc., is a global leader in the design and manufacture of precision, programmable power supplies for R&D, test and measurement, process control, power bus simulation and power conditioning applications across diverse industrial segments. From bench top supplies to rack-mounted industrial power subsystems, AMETEK Programmable Power is the proud manufacturer of Elgar, Sorensen, California Instruments and Power Ten brand power supplies.

SOR-DS-SG-Datasheet

The Sorensen SG Series (hereafter SG Series) represents the next generation of high power programmable DC power supplies. The SG Series is designed for exceptional load transient response, low noise and the highest power density in the industry. With a full 15 kW available down to 20VDC output in a 3U package the SG leads the industry in power density. The power density is enhanced by a stylish front air intake allowing supplies to be stacked without any required clearance between units.

SN-DS-i1a-magnetic-transducer

The I1A denotes a range of SENIS Magnetic Fieldto-Voltage Transducers with integrated 1-axis Hall Probe. It measures magnetic fields perpendicular to the probe plane (By).

SN-DS-hall-probe-k-for-f1a-mft

Hall Probe K for F1A Magnetic Transducers with the naked Si chip is a very thin (0.5mm) and long (47mm) single-chip fully integrated 1-axis Hall-Probe. It measures magnetic fields perpendicular to the probe plane (By).

SN-DS-hall-probe-h-for-i1a-mft

Hall Probe H for F1A Magnetic Transducers is a very thin (1.1mm) and long (42mm) single-chip integrated 1-axis Hall-Probe. It measures magnetic fields perpendicular to the probe plane (By).

SN-DS-hall-probe-g-for-i1a-mft

Hall Probe G for F1A Magnetic Transducers with the naked Si chip is a very thin (0.5mm) and long (42mm) single-chip integrated 1-axis Hall-Probe. It measures magnetic fields perpendicular to the probe plane (By).

Shape-B-SMA

CURRENT TRANSFORMER- SHAPE B/SMA CONNECTOR CURRENT TRANSFORMER- SHAPE B/SMA CONNECTOR

Shape-B-BNC

CURRENT TRANSFORMER- SHAPE B/BNC CONNECTOR CURRENT TRANSFORMER- SHAPE B/BNC CONNECTOR

Shafer-BPM

The purpose of this paper is to review the topic of beam position monitoring as it applies to charged-particle beams in accelerators and beamlines.

SENIS-CAT-Magnetics

Based on the pioneering work of Robert E. Shafer at Los Alamos Laboratory, the Log-Ratio BPM derives beam position from logarithm of the ratio of opposite pickup signals: Log(A/B).

RCTrms-Technical-notes

All measuring instruments are subject to limitations. The purpose of these technical notes is to explain some of those limitations and to help the engineer maximise the many advantages of PEM’s Rogowski current transducers. These technical notes should be read in conjunction with the RCTrms short-form datasheet.

Principle-of-Zero-Flux-CTs

The primary current, ??, in a conductor through a magnetic core will generate a magnetic flux in the core ????.

PPM-DS-p2p-DCLink

The new DC point2point link is capable of transmitting analogue signals of up to 40MHz over singlemode fibre. This is equivalent to rise times of 10.3ns making it ideal for measuring HV transients on HVDC transmission lines. The modules are available in a fully EM shielded casing, or as a plug-in module for use with the various point2point housings.

PPM-DS-p2p-BatterySwitch

APPLICATIONS • Compatible with all point2point products. • Compatible with all battery technologies • Provide remote control of modules via a multimode fibre • Long distance transmission, will work in excess of 1km • Provide a fully isolated control signal with very high levels of shielding and immunity.

PEM-TN-CWT-DelayAndRiseTime

The CWT behaviour at frequencies approaching and exceeding its specified (-3dB) bandwidth is very complicated. It is related to the distributed inductance and capacitance of both the Rogowski coil and the connecting co-axial cable (which have different characteristic impedances) and their terminations, and to the gain-frequency characteristic for the op-amps and associated parasitic impedances used to implement the integrator and buffer electronics. It also varies depending on the position of the current within the loop, although up to the (-3dB) bandwidth this variation is very small.

OM1938-Magnetic-Shield

Operation Manual for TLMS-O100 Open-End Magnetic Shield TLMS-C100 Capped-End Magnetic Shield

MX-BPM.manual.Spear3

MX-BPM User’s Manual Spear-3 options MX-BPM User’s Manual Spear-3 options

MS2-RS232-Cable-DR1615

MS2 RS232 Cable MS2 RS232 Cable MS2 RS232 Cable MS2 RS232 Cable

MS2-OM0408

Operation Manual for MS2 Magnetic Susceptibility System

MS2B-DR0305

MS2B-DR0305 MS2B-DR0305 MS2B-DR0305 MS2B-DR0305 MS2B-DR0305

Model_5201_mapa_data

Model 5201 Projected Field Electromagnet Field Map Data

MMS-1A-RS-Operating-Manual_US

Magnetic Field Mapper MMS-1A-RS is the high-end version of the SENIS Magnetic Field Mapping Systems. It allows users to perform a fast, high resolution mapping of magnetic flux density around permanent magnets, electromagnets or electronic circuit boards. The map of the magnetic field can be presented as color coded 2D or 3D visual displays on a PC screen and as a table of numerical measured values. Measured data are analyzed in real-time, which provide data analysis capabilities for an advanced inspection, characterization and quality control of permanent magnets.

ML_MAN_PT2025

The PT 2025 NMR Teslameter System (Fig. 1) comprises the following: · Bench-top main unit with RS 232C and (as an option) IEEE-488 interfaces · At least one NMR probe · A multiplexer if several probes are required

MFC3039

ASSEMBLY INSTRUCTIONS FOR THE MFC-3039 ROTATING PROBE-ARRAY HOLDER

Matesy-MO-PRES-SometimesPerspectiveDoesMatter

The magneto-optical technology is an imaging method for magnetic measurement, forensic investigation and non-destructive testing. The magneto-optical wafers provide field analysis and quality assurance of different magnetic materials. Magneto-optical wafers with different measuring ranges are available in standard sizes, customized geometries and as sensor array up to 100 x 100 mm.

Matesy-MO-ARTICLE-MagnetoOpticalSensors

The use of magnetic materials for manufacturing and in research has grown dramatically. The importance of magnetic measurement and testing applications will continue to rise corresponding to technological trends such as electric mobility, robotics, miniaturization and automation technologies, as well as promising magnetic materials (e.g., polymer-bonded magnets and magnetic shape memory alloys). At the same time, growing demand for sensors for use in static and dynamic magnetic measurement applications have pushed established sensor technologies to their limits. Magneto-optical sensor technology offers entirely new perspectives in the field of magnetic measurement and testing.

Matesy-MAN-CMOS-MagView

The CMOS-MagView is an innovative device for the optical visualization of magnetic fields. The highly engineered magneto-optial sensor technology visualize the magentic stray field of magnetic materials directly and at high optical resolution. The magneto-optical analysis of the test specimen provides concrete information about the field polarity, field homogeneity, distribution of the magnetic material and the magnetization properties.

Matesy-DS-MiniMo

Being a small and light testing device, Minimo can be used as a stationary and mobile system for fast visualization of magnetic stray fields. The webcam-based Minimo is applicable for a qualitative examination of magnetic stripe cards, removed serial numbers and hard magnetic material structures. In addition to plug-and-play ability and image archiving a simple change of the magneto-optical sensor head is possible. Minimo can be equipped with all types of magneto-optical sensors. This allows an adaption of the Minimo to the sample field strength.

Magnetic1-Shields-DS0014

Magnetic Shields Very Low Magnetic Field Test Facilities

Mag690U-DR2737

Mag690U Outline Drawing Mag690U Outline Drawing Mag690U Outline Drawing

Mag690-MX-DR2690

Mag690-MX Outline Drawing Mag690-MX Outline Drawing

Mag670-DS2497

Mag670-DS2497 Mag670 Low Cost Single Axis Magnetic Field Sensor

ew-712b_gmw

EW-712B is composed of a Ultra-high sensitive InSb Hall element and a signal processing IC chip in a package.

ew-650B_gmw

EW-650B is composed of a Ultra-high sensitive InSb Hall element and a signal processing IC chip in a package.

EW-632

EW-632 is composed of a Ultra-high sensitive InSb Hall element and a signal processing IC chip in a package.

ew-450_gmw

EW-450 is composed of a Ultra-high sensitive InSb Hall element and a signal processing IC chip in a package.

ew-412b_gmw

EW-412B is composed of a Ultra-high sensitive InSb Hall element and a signal processing IC chip in a package.

EQ-732L_MS-1380-E-00_120508-gmw

• Analog output voltage proportional to the magnetic flux density • Magnetic sensitivity 40mV/mT (typ.) • Supply voltage from 3.0V to 5.5V at single power supply • Operating temperature range from -40°C to 100°C • Ratio-metric analog output • 3pin single in-line package (SIP), Halogen free • Quick response 1μs (typ.) • Low output noise voltage 3mVp-p

EQ-730L_MS-1378-E-00_120508-gmw

• Analog output voltage proportional to the magnetic flux density • Magnetic sensitivity 130mV/mT (typ.) • Supply voltage from 3.0V to 5.5V at single power supply • Operating temperature range from -40°C to 100°C • Ratio-metric analog output • 3pin single in-line package (SIP), Halogen free • Quick response 2μs (typ.) • Low output noise voltage 10mVp-p

eq-433l_e

EQ-433L is composed of an InAs Quantum Well Hall Element and a signal processing IC chip in a package Notice:It is requested to read and accept "IMPORTANT NOTICE" written on the back of the front cover of this catalogue.

EPO_Control_Users_Manual_Pages

EPO_Control_Users_Manual_Pages USER’S MANUAL EPO CONTROL

em-1781_gmw

EM-1781 is ultra-small Hall effect ICs of a single silicon chip composed of Hall element and a signal processing IC.

DTM-151-G_Manual_-S5

DTM-151 DIGITAL TESLAMETER with IEEE-488 GPIB Interface USER’S MANUAL

DTM-133-wGPIB-Manual

DTM-133 DIGITAL TESLAMETER with serial communications USER’S MANUAL

DTM-130-G-DTM-141-G-Manual

Complete 4-channel system interface unit for ultra-stable, high precision fluxgate tech-nology DS series current transducers.

DTM-130-141

Fully configurable dedicated 6-channel system interface unit for ultra-stable, high pre-cision fluxgate technology DS series current transducers.Powers up to 6 x DS50 to DS2000 at the same time.Supports calibration windings and has 6 slots for optional voltage output modules VOM (1V or 10V)

DS-HTS-110-LM

Applications HTS-110’s LM range is suitable for various applications, including: 4 MOKE (Magneto-optic Kerr effect) 4 Magnetic domain imaging 4 Brillouin light scattering 4 Magnetic circular dichroism 4 Hysteresis loop plotting 4 Scanning laser microscopy 4 Hall effect measurements 4 Variable temperature optical cryostat

DS600UB-1V

Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 950A

DS600ID

Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 1000A

DR2390

Mag648-MX and Mag649-MX outline drawing Mag648-MX and Mag649-MX outline drawing

DR0624

DR0624 Mag-03MS sensor outline with mating connector

DL2000ID-CD100

Ultra-stable, high precision (ppm class) fluxgate technology DS Series current transducer for non-intrusive, isolated DC and AC current measurement up to 3000A

Datasheet_DC200IF

Highly stabilized and precise fluxgate technology based current transducer, re-engineered for cost sensitive, non-intrusive, isolated DC and AC current measurement applications up to 300A

CZ-3705

CZ-3705 is an open-type current sensor using Hall sensors, which outputs the analog voltage proportional to the AC/DC current. Group III-V semiconductor thin film is used as the Hall sensor, which enables the high-accuracy and high-speed current sensing. Coreless ultra-small surface mount package realizes the space-saving.

CZ-3702

CZ-3702 is an open-type current sensor using Hall sensors, which outputs the analog voltage proportional to the AC/DC current. Group III-V semiconductor thin film is used as the Hall sensor, which enables the high-accuracy and high-speed current sensing. Coreless ultra-small surface mount package realizes the space-saving.

CWTUM-Dimensions

Positional accuracy and external currents Due to small variations in the winding density and coil cross sectional area the transducer output varies slightly depending on the position of the current in the coil and also the size of the current conductor relative to the coil.

cwtlf

PEM?s Rogowski Current Waveform Transducers combine high bandwidth, safety, and the minimum disruption to the circuit under test. These instructions should be followed whenever the unit is used. They are intended to help you obtain the best and safest performance from the transducer

CWT-instructions

PEM?s Rogowski Current Waveform Transducers combine high bandwidth, safety, and the minimum disruption to the circuit under test. These instructions should be followed whenever the unit is used. They are intended to help you obtain the best and safest performance from the transducer

CWT_Fuse_Replace_Instructions_GMW

Instructions for CWT Integrator Module Fuse Replacement

cwctmanual

CWCT & BCM-CW-E CW Current Transformer Beam Charge Monitor for CW beams and Macropulses User’s Manual

CU2-DR3999

CU2-DR3999 Operation Manual for CU2 Closed Loop Module

CT-04.10.Tech_.note

For personnel and equipment safety and measurement accuracy, current measurements on conductors at high voltage should be made only with a conducting shield cylinder placed inside the CT aperture. There should be a low electrical impedance connection from one end only to a reliable local ground. An inner insulating cylinder of adequate voltage isolation should be between the shield cylinder and the conductor at high voltage. Any leakage, induced or breakdown current between the high voltage conductor and the ground shield will substantially pass to local ground rather than through the signal cable to signal ground. Do not create a "current loop" by connecting the shield cylinder to ground from both ends. Current flowing in this loop will also be measured by the CT.

CS016-metrolab

Like Bartington Instruments, Metrolab Technology SA builds magnetometers.The key difference is that Metrolab’s magnetometers are designed for very strong fields. One of its product lines is a range of three-axis Hall effect magnetometers able to resolve up to 2μT, but even this is insufficient for some purposes. Metrolab has now been able to extend the resolution into the nT range, thanks to Bartington’s Mag649 low-power three-axis fluxgate sensor.

CQ-3301

CQ-3301 is an open-type current sensor using a Hall sensor which outputs the analog voltage proportional to the AC/DC current. Quantum well ultra- thin film InAs (Indium Arsenide) is used as the Hall sensor, which enables the high-accuracy and high-speed current sensing. Coreless surface mount package realizes the spacesaving.

CQ3201

CQ-2366 is an open-type current sensor using a Hall sensor which outputs the analog voltage proportional to the AC/DC current. Quantum well ultra-thin film InAs (Indium Arsenide) is used as the Hall sensor, which enables the high-accuracy and high-speed current sensing. Simple AI-Shell package with the Hall sensor, magnetic core, and primary conductor realizes the space-saving and high reliability.

CQ-2334

CQ-2334 is an open-type current sensor using a Hall sensor which outputs the analog voltage proportional to the AC/DC current. Quantum well ultra-thin film InAs (Indium Arsenide) is used as the Hall sensor, which enables the high-accuracy and high-speed current sensing. Simple AI-Shell package with the Hall sensor, magnetic core, and primary conductor realizes the space-saving and high reliability.

CQ2064

CQ-2064 is an open-type current sensor using a Hall sensor which outputs the analog voltage proportional to the AC/DC current. Quantum well ultra-thin film InAs (Indium Arsenide) is used as the Hall sensor, which enables the high-accuracy and high-speed current sensing. Simple AI-Shell® package with the Hall sensor, magnetic core, and primary conductor realizes the space-saving and high reliability.

CQ3_Series_Application_Note

CQ3_Series_Application_Note CQ3_Series_Application_Note

CPCO-XXXX-160-07

The CPCO Series (160mm) Current Probes are Clamp On current sensors capable of measuring ac and dc currents available in ranges of ±4000A ±8000A, ±12000A with an accuracy of +/-1% and non-linearity of <+/- 0.5%. The bandwidth is dc to 40kHz. The Current Probe splits along a diameter allowing easy installation to existing cables without having to break the connection. A captive screw is used rather than a clip to ensure consistent closure under mechanical loading or vibration.

CPCO-Technical-Notes

SE Option - The SE stands for Single Ended and the output voltage from the CPCO will have a quiescent output voltage of 5.0V when there is no primary current (IPRI=0A). As the primary current (IPRI) increases in a positive direction, the output voltage will increase to the maximum level of 10.0V at IPRI=IPSAT. When the primary current increases in the negative direction, the output voltage will decrease toward 0.0V at IPRI=-IPSAT

BSS-02B section through coil & nose cone

BSS-02B section through coil & nose cone BSS-02B section through coil & nose cone

BSS-02B outline drawing

BSS-02B outline drawing BSS-02B outline drawing BSS-02B outline drawing

BSS-02B-electronic-interface

BSS-02B-electronic-interface BSS-02B electronic interface

BPM-AFE.11flyer

BPM-AFE is an analog frontend to process RF signals from beam position pickup electrodes. It delivers an output signal which can be directly entered into fast 14-bit ADCs. It is specially developed for transfer lines and linacs. It can be customized to any RF frequency up to 1 GHz.

BI-MAG-01-CryogenicProbeDrawing

Low temperature Mag Probes type F (0.2mT) and type G (2.0mT)

BI_MAN_MAG03MC-CU-MAG03MS-CU-issue

BARTINGTON MAG-03MC-CU & MAG-03MS-CU CALIBRATION UNIT OPERATION MANUAL

BI_mag690_FrequencyResponse_Charts

Mag690 Three-Axis Fluxgate Field Sensor, Amplitude and Phase Response v Frequency

BBC

Beam-based methods to measure BPM?s center offset with reference to the pickup center and BPM?s resolution are proposed. Being built in a BPM, the methods provide a BPM verification by its own means.

BB-BPM-Datasheet

For cancer therapy synchrotrons Tracks the beam during energy ramp

Bartsoft-PC-OM2647

Bartsoft software acquires, corrects, displays, stores and prints data using Bartington Instruments MS2 and MS3 meters. This guide explains how to use the software and helps the user understand how it works, including the function of all controls and windows.

app-note-hts-1101-01

APPLICATION NOTE: HTS110-01 END CAP RESISTANCE AND HEAT SINKING FOR HTS CURRENT LEADS

AN0039-Mag648-used-for-maritime-perimeter-surveillance

To detect small magnetic field fluctuations caused by movement of nearby ferromagnetic objects, thus indicating the presence of divers or small vessels

AN0028-Mag-01H-DI-used-in-Absolute-Declination-and-Inclination-Measurements

To calculate absolute values of declination and inclination in the Earth’s magnetic field at a specific location, for accuracy of magnetic measurements.

AN0026-Mag-03-used-to-measure-ELF-magnetic-field-emissions-from-mobile-phones

To measure ELF (extremely low frequency) magnetic fields produced by mobile telephone handsets.

AN0024-Mag-03-and-Spectramag-6-used-in-magnetic-hygiene-tests-of-spacecraft-components

Pre-installation EMC testing (electromagnetic compatibility) of components, and pre-launch EMC testing of spacecraft.

AN0020-The-use-of-Bartington-Fluxgate-Magnetometers-in-MT

Applications include mineral prospection,hydrogeology, geothermal and oil exploration,astrophysics, and earthquake studies.

AN_133KIT-Spec

The AN_133KIT consists of a EM-3242 angle sensor mounted on a small 0.25 in. square PCB with a 6 in. flat cable. Also included in the kit are three SmCo24 magnets compatible with the angle sensor; a 0.25 in. diameter magnet, a 0.15 in. diameter magnet and a 0.25 in. square magnet. The sensor works well with smaller magnets, but with less air gap. See Reference Design RD101_EM3242 for details.

Ametes_360ASM_Spec

FEATURES • Analog and PWM outputs for 0 ± 180 degrees • 10% to 90% active range output signals • Resolution of up to 9 bits • Magnet “Out of Range” discrete output • User selectable “Zero Angle” set • No external parts required • Single 5V supply • Small 1/2” dia encapsulated package

AKM-Current-Sensor-Parameter-Selection-Chart

AKM Currentier Series of Current Sensing IC's Test Printed Circuit Boards

ak8772_e

●Features ?Precision Bipolar Hall Effect Latch ?Power manageability through "PDN" pin 　Current consumption in Power down mode is less than 1μA ?Low current consumption at active mode : less than avg. 　150μA@VDD=3V ?Ultra small SON package : 1.1×1.4×t0.37mm, Halogen free

Adaptors

Precise waveform measurement of long pulses and macropulses up to several milliseconds with minimal droop and noise.

ACCT-S-245-MSH

Precise waveform measurement of long pulses and macropulses up to several milliseconds with minimal droop and noise.

ACCT-S-122

Precise waveform measurement of long pulses and macropulses up to several milliseconds with minimal droop and noise.

ACCT-S-075-MSH

Precise waveform measurement of long pulses and macropulses up to several milliseconds with minimal droop and noise.

A_Mercury-Manual-Final

The Mercury Series chillers are designed to be used per the instructions in this manual. Used in any other fashion it may not perform to specification and may be less safe to operate in general. Failure to heed warnings and instructions listed in this manual may void the warranty, damage the unit, damage other equipment and possibly cause serious personal injury.

17900-2211-0-Outline-Dwg

The 3480 dipole electromagnet is a light weight versatile system that can provide fields approaching 4 Tesla. At 34 kg this magnet can easily be moved between applications and can be operated in any orientation.

17900-2210-0-Outline-Dwg

The 3480 dipole electromagnet is a light weight versatile system that can provide fields approaching 4 Tesla. At 34 kg this magnet can easily be moved between applications and can be operated in any orientation.

17900-2172-0

The 3480 dipole electromagnet is a light weight versatile system that can provide fields approaching 4 Tesla. At 34 kg this magnet can easily be moved between applications and can be operated in any orientation.

11907-0399-1_A_Gimbal_Mount_3472-70_System

Model 3472 System Installation; Minimum Facility Requirements for High Precision Systems and Systems with Field Reversal installed in North America

11907-0355-0_S3_C_3480_General_Assembly

The 3480 dipole electromagnet is a light weight versatile system that can provide fields approaching 4 Tesla. At 34 kg this magnet can easily be moved between applications and can be operated in any orientation.

5203_Eaton_Interlock_Logic

In an interlock event the protected power lines are disconnected, the unprotected lines remain powered. In this case, the power supplies lose power and the magnet is inert, the PC remains on.

3480 Uniformity PoleGap PoleFace 35A

The 3480 OG dipole electromagnet is a light weight versatile system intended to provide an open geometry particularly suited to MOKE applications. At 32 kg this magnet can easily be moved between applications and can be operated in any orientation.

3480_17907-0728-0_C_Tapered_Sleeve

The 3480 dipole electromagnet is a light weight versatile system that can provide fields approaching 4 Tesla. At 34 kg this magnet can easily be moved between applications and can be operated in any orientation.

3473-70-Fringe-Field

Model 3473 System Installation; Minimum Facility Requirements for High Precision Systems and Systems with Field Reversal installed in North America

55C0126

This manual contains all relevant information on the steps, which are necessary to start the 3MTS Teslameter software installation and to operate it properly, once the 3MTS is connected to the PC or Tablet via the delivered USB cable. All files, including the software, user manuals and calibration data have been stored on the 3MTS USB flash memory stick, which is a part of the Teslameter package

2SA10

Sentron’s new magnetic angular sensor 2SA-10 detects the absolute angular position of a small magnet that is positioned above the device surface. The 2SA-10 is an integrated combination of a CMOS Hall circuit and a thin ferromagnetic disk. The CMOS circuit contains two pairs of Hall-elements for each of the two directions parallel with the chip surface X and Y. The ferromagnetic disk amplifies the external magnetic field and concentrates it on the Hall elements.

1DSA-05-Dif-to-Sin-Adap

The 1DSA-05 converts a differential voltage into a corresponding single-ended voltage with respect to an external ground reference. The 1DSA-05 can be used as an extension of the electronic module (Module E) of SENIS’s single-axis magnetic flux density to voltage transducers: it enables measurement of the transducer output voltage using the instruments that have singleended inputs (such as oscilloscopes).

SPI-Module™ Sputter/Carbon Coater System™

The SPI Supplies Sputter/Carbon coating system allows the flexibility to choose between carbon evaporation and metal sputtering, all in the same system.

SPI Plasma Prep III™

The Plasma Prep III is the latest member of our Plasma Prep family. The system incorporates solid-state technology, including an integrated vacuum gauge. As part of its low cost design, the system comes single gas inlet. The addition of the optional Process Control Module expands the system, and allows precise mixing of multiple gasses, as well as the ability to automatically shut the system down when the process is complete.

05001/05002/05005 S Paint S Streaker MSDS

Structure Probe Inc. / SPI Supplies confirms that: 05001-AB, 05002-AB, 05002-GA, 05002P-AB, and 05002-GA Silver Conductive Paint are RoHS2 compliant, fulfilling the definitions and restrictions defined under Directive 2011/65/EC of the uropean Parliament and of the Council of 21 July 2011.

SPI Supplies ® Graphene Products

The use of graphene in research is a growing area requiring a source of high quality materials and substrates. SPI Supplies now offers a source of graphene in various forms*. Using a unique patented CVD process, these graphene films are clean and uniform.SPI Supplies currently offers graphene as support films on TEM grids or on copper substrates.

NIST and NPL

NIST and NPL (NIST counterpart in the U.K.) traceable - Certified Reference Material. A Magnification Reference Standard designed for Microscopy by Microscopists.

Apiezon Wax W MSDS

Apiezon waxes are versatile products offering a multitude of uses. The key applications and features of the products are shown in the table opposite.

美国ARS公司CS210AE-GMX-1SS高效型闭循环无液氦低温恒温器

X-1SS高效型低温恒温器拥有不锈钢真空外罩及仪表群。配以合适的真空系统该套恒温器真空度可达10-7 Torr，更高的真空度会有效防止样品表面污染。 镍镀金无氧铜铜防热辐射屏耐用，热辐射低，是低温实验下理想的防热辐射材料。 X-1SS系列恒温器可配备DE-202、DE-204或DE-210系列冷头，根据客户需要可选择4K，5.5K，10K不同型号。

美国ARS公司CS204AI-FMX-1SS高效型闭循环无液氦低温恒温器

X-1SS高效型低温恒温器拥有不锈钢真空外罩及仪表群。配以合适的真空系统该套恒温器真空度可达10-7 Torr，更高的真空度会有效防止样品表面污染。 镍镀金无氧铜铜防热辐射屏耐用，热辐射低，是低温实验下理想的防热辐射材料。 X-1SS系列恒温器可配备DE-202、DE-204或DE-210系列冷头，根据客户需要可选择4K，5.5K，10K不同型号。

美国ARS公司CS202AI-DMX-1SS高效型闭循环无液氦低温恒温器

典型特点 l 无需消耗制冷剂 l 更高真空的不锈钢焊接结构 l 1.25 英寸的大光学窗口 l 大样品视角利于光学采集(F/.8) l 可任意方向操作 l 可根据客户要求进行定制 可选配置及升级选项 l 4 K 冷头 l 5.5 K 冷头 l 450 K高温台 l 800 K 高温台 l 可定制温度计结构 l 可定制接线结构 l 可定制窗口材料 l 可定制样品座

美国ARS CS210AF-GMX-19OP-顶端装载光学型闭循环低温恒温器

X-19OP是顶端装载样品的光学型恒温器，样品置于氦气交换气体腔，使用样品杆更换样品，换样时无需关闭制冷机，这样的设计换样速度快，特别适合需要进行大量样品测试情况。而且样品置于冷的氦气环境中，适用于各种导热性不好的样品降温。 X-19OP系统有大的光学通路，可选择不同窗口适合各种光学实验。