上海博取PH8010污水PH电极

PH8010型工业复合污水PH电极

PH电极基本原理
    PH测量中使用的电极又称为原电池。原电池是一个系统，它的作用是使化学能量转成为电能。此电池的电压被称为电动势（EMF）。此电动势(EMF)由二个半电池构成。其中一个半电池称作测量电池，它的电位与特定的离子活度有关；另一个半电池为参比半电池，通常称作参比电极，它一般是与测量溶液相通，并且与测量仪表相连。
技术参数：
    型    号：    PH8010
测量范围：    0-14PH
温度范围：    0-85℃
耐    压：    0.6MPa
材    质：    PPS/PC
斜    率：    >96%
零点电位：    7PH ±0.3
安装尺寸：    上下3/4NPT管螺纹
连接方式：    低噪音电缆线直接引出
应    用：    用于各种工业废水、环保及水处理
特   点： 
   采用国际最先进的固体电介质和大面积聚四氟乙烯液接界。不易阻塞，维护方便长距离的参比扩散途径，极大的延长了电极在恶劣环境中的使用寿命内置温度传感器（可根据用户要求选用Pt100,Pt1000或NAT等）温度使用范围广，内置温度传感器，可用于防爆区域新型设计的玻璃球泡，增加了球泡面积，防止内缓冲液中干扰气泡的生成，使测量更加可靠采用PPS/PC外壳，上下3/4NPT管螺纹，安装方便，不需要护套，节省了安装成本电极集中pH、参比、溶液接地、温补于一体，溶液接地与参比联结可作ORP使用电极采用优质低噪音电缆线，可使信号输出长度大于20米以上、无干扰 该电极采用超底阻抗敏感玻璃膜制成、在低电导、高纯水场合下、同样具有响应快、测量准、稳定性好、不易水解的特点。

PH8010 industrial composite sewage PH electrode

The basic principle of PH electrode

PH measurement is used in the electrode is also known as the primary battery. Primary battery is a system, it is the role of the chemical energy into electrical energy. The battery voltage is called electromotive force ( EMF ). The electromotive force ( EMF ) consists of 2.5 batteries. Among the 1.5 cell called the measuring cell, its potential and specific ion activity; the other 1.5 battery as the reference half cell, often referred to as a reference electrode, it is generally associated with the measurement of solution are communicated, and measuring instrument.

Technical parameters:

Model No.: PH8010

Measuring range: 0-14PH

Temperature range: 0-85℃

High pressure: 0.6MPa

Material: PPS/PC

Ramp rate: >96%

Zero potential: 7PH ± 0.3

Installation size : the next 3/4NPT pipe thread

Connection: low noise cable lead directly to

Use: used for all kinds of industrial wastewater, environmental protection and water treatment

Special:

The use of the international most advanced solid dielectric and a large area of PTFE liquid junction. It is not easy to be blocked, convenient maintenance and long distance reference diffusion pathways, greatly extending the electrode in the harsh environment of the service life of a built-in temperature sensor ( according to the requirements of users can choose Pt100, Pt1000 or NAT ) temperature and wide range of use, a built-in temperature sensor, can be used for explosion-proof area model design of glass bulb, increase the bulb area, prevent the internal buffer interference with bubble generation, make the measurement more reliable by using PPS/PC casing, upper and lower 3/4NPT pipe thread, convenient installation, does not need the sheath, save installation cost electrode concentration pH, reference, solution temperature compensation in one grounding, grounding, solution and reference connection can ORP uses electrodes using high quality low noise cable, the signal output of length greater than 20 meters, without interfering with the electrode adopts the bottom impedance sensitive glass film, in the low conductance, high water situation, also has the advantages of fast response, good stability, measurement, uneasy hydrolysis characteristics。