S.G.Frantz磁除铁器

弗朗茨^®磁除铁器利用一堆不锈钢网格磁化的永磁体收集即使最微小的颗粒。这是从其他磁选机和常规，成百上千个网格划分和再划分边脚千流，所有粒子都要通过一系列性的强磁场的过滤器和过滤器的根本不同。

PQ ferrofilter系列^®永磁磁选机的额定工作压力在100 psi。因为他们的低压降，它们通常会被安装在吸气侧保护泵磨损。

磁选机的应用

理想的使用在各种各样的环境，我们的磁除铁器已在以下应用数十年的成功：

?重型设备-提取磨粒磨损的移动部件在发动机和其他机械油润滑以防止磨损和损坏轴承，齿轮和其他运动部件

?液压系统-安装在吸气侧液压系统去除锈斑、规模和精细的金属磨损颗粒，并保护液压泵和阀的磨损，粘着磨损

?冷却系统–去除细小金属颗粒从冷却液泵（安装前和/或后）未能解决在水池的提高完成工作，延长刀具寿命，提高生产

?挥发性液体–提供安全过滤的燃料、油漆、溶剂、碳氢化合物等挥发性液体中去除污染物（无风险的地方有爆炸的危险）

?仪表和控制–去除金属颗粒太小被边缘型过滤器、机械过滤器、保护米和控制故障

?锅炉和蒸汽系统–清除堆积的铁锈和水垢降低污染物（这妨碍阀门的操作）和提高运营效率的锅炉和泵

?过滤系统–延长寿命的过滤系统去除污染物，可通过细网格或超载

?试验站–守卫新设备免受损害，消除细钢和铁颗粒，积累过程中的加工、制造和装配的零部件

优点ferrofilter^®除铁器

由于其独特的设计，永磁磁选机提供了几个明显的优势：

<?细颗粒去除–他们能够去除微小颗粒的钢铁生锈或规模。

?低维护–因为网格几乎坚不可摧，在正常使用的情况下，他们不需要经常更换。

?寿命长–由于没有运动部件磨损，使用寿命几乎是无限的。

?全流量，低压力降–ferrofilter^®永磁磁选机是大容量的分离器设计的全流式安装，没有旁路。设计广泛的选择提供了从几乎任何粘度的液体，有效去除污染物，无堵塞、低压降。

?简单，紧凑，方便–ferrofilter^®永磁除铁器容易适合管道或可直接连接设备，管道（但所有的部件都是现成的清洗）。

?易于清洁–网格叠加是退磁时从磁铁分离，便于清洁。

磁选机规格

清洗

所有型号的ferrofilter^®永磁除铁器容易打开清洗。网格叠加是退磁时从磁体分离。需要清洁的频率取决于应用：一般需要一周或一个月为一个ferrofilter^®在正常使用中的机械润滑系统的永磁磁选机；从一到六个月为一个ferrofilter^®在液压系统中永磁分离器；至少一次每八小时轮班一ferrofilter^®永磁磁选机清洗液在钻、镗等加工业务；每个运行在新机器后。

PQ系列永磁磁选机

我们提供五种不同的永磁除铁器，从2（约一个汽车油过滤器的大小）对PQ6（我们最大的永磁磁选机，一个容量20倍的示意图）。无论你需要什么，S.G. Frantz^®有能力帮助你找到合适的分离方法。联系我们与我们经验丰富的技术人员。

Permanent Magnet Separator Applications

Ideal for use in a wide variety of environments, our Permanent Magnet Separators have been performing successfully in the following applications for decades:

? Heavy Equipment – Extracting abrasive particles worn from moving parts in engines and other oil-lubricated machinery to prevent wear and damage to bearings, gears and other moving parts

? Hydraulic Systems – Installed in the suction side of hydraulic systems to remove rust, scale and fine metal wear particles, and to protect hydraulic pumps and valves from abrasion, sticking and wear

? Coolant Systems – Removing fine metal particles from coolant pumps (installed before and/or after) which fail to settle out in the sump to improve the finish of the work, extend tool life and increase production

? Volatile Liquids – Providing safe filtration of fuels, paints, solvents, hydrocarbons and other volatile liquids to remove contaminants (without risk in locations where there is danger of explosion)

? Meters and Controls – Removing metal particles too small to be captured by edge type filters or mechanical strainers, protecting meters and controls from malfunction

? Boiler and Steam Systems – Removing accumulated rust and scale to reduce contaminants (which interfere with the operation of valves) and increase the operational efficiency of boilers and pumps

? Filtration Systems – Extending the life of filtration systems by removing fine contaminants that could pass through grids or overload them

? Test Stands – Guarding new equipment against damage by removing fine iron and steel particles, which accumulate in the course of the machining, fabricating and assembling of its parts

Advantages of FerroFilter^® Permanent Magnet Separators

Thanks to their unique design, Permanent Magnet Separators offer several distinct advantages:

? Fine Particle Removal – They are able to remove microscopic particles of iron and steel rust or scale.

? Low Maintenance – Because grids are virtually Indestructible under normal use, they don't require constant replacement.

? Long Service Life – Because there are no moving parts to wear out, service life is virtually unlimited.

? Full Flow, Low-Pressure Drop – FerroFilter^® Permanent Magnet Separators are high-capacity separators designed for installation in the full flow, not in a by-pass. A wide choice of designs provides effective removal of contaminants from fluids of virtually any viscosity, without clogging and with low-pressure drop.

? Simple, Compact, Accessible – FerroFilter^® Permanent Magnet Separators fit easily into pipelines or can be bolted directly to equipment without piping (yet all parts are readily available for cleaning).

? Easy to Clean – The grid stack is demagnetized when it is separated from the magnets, making it easy to clean.

Permanent Magnet Separator Specifications

Cleaning

All models of FerroFilter^® Permanent Magnet Separators are easily opened for cleaning. The grid stack is demagnetized when it is separated from the magnets. Frequency of cleaning required depends on the application: Generally it should be from a week to a month for a FerroFilter^® Permanent Magnet Separator in the lubrication system of machinery in regular service; from one to six months for a FerroFilter^® Permanent Magnet Separator in a hydraulic system; at least once in each eight-hour shift for a FerroFilter^® Permanent Magnet Separator cleansing coolants in drilling, boring and other machining operations; and after each run-in of new machinery.

Series PQ Permanent Magnet Separators

We offer five different permanent magnet separators, ranging from the PQ2 (approximately the size of an automobile oil filter) to the PQ6 (our largest permanent magnet separator, with a capacity 20 times that of the PQ2). Whatever your needs, S.G. Frantz^® has the expertise to help you find the right separation solution. Contact us today to speak with one of our experienced and knowledgeable technicians.