您好,欢迎访问仪器信息网
注册
上海希美化学有限公司

关注

已关注

已认证

粉丝量 0

当前位置: 上海希美化学 > ELISA试剂盒 > 大鼠甲状腺素抗体(TAb)ELISA Kit

大鼠甲状腺素抗体(TAb)ELISA Kit

供货周期: 一周
品牌: Cusabio
规格: 96T
货号: CSB-E08473r
CAS号: CSB-E08473r
报价: ¥1
留言咨询
产品介绍

大鼠甲状腺素抗体(TAb)酶联免疫吸附测定试剂盒使用说明书
本试剂盒仅供体外研究使用、不用于临床诊断!

产品名称: 大鼠甲状腺素抗体(TAb)ELISA Kit
英文名称: Rat Thyroxine antibody,TAb ELISA Kit
货号: CSB-E08473r
规格: 96T
种属: Rat
待测物名称: Thyroxine antibody,TAb
反应时间: 1-5h
所需样本体积: 50-100ul
检测波长: 450 nm

大鼠甲状腺素抗体(TAb)ELISA Kit

预期应用
ELISA法定量测定大鼠血清、血浆或其它相关生物液体中TAb含量。

大鼠甲状腺素抗体(TAb)ELISA Kit

实验原理
用纯化的TAb抗体包被微孔板,制成固相载体,往微孔中依次加入标本或标准品、生物素化的TAb抗体、HRP标记的亲和素,经过彻底洗涤后用底物(TMB)显色。TMB在过氧化物酶的催化下转化成蓝色,并在酸的作用下转化成最终的黄色。颜色的深浅和样品中的TAb呈正相关。用酶标仪在450nm波长下测定吸光度(OD值),计算样品浓度。

大鼠甲状腺素抗体(TAb)ELISA Kit

试剂盒组成及试剂配制
1、 酶标板:一块(96孔)
2、 标准品(冻干品): 2瓶,请临用前15分钟内配制。每瓶以样品稀释液稀释至1ml,盖好后室温静置大约10分钟,同时反复颠倒/搓动以助溶解,其浓度为100 nmol/L,然后做系列倍比稀释(注:不要直接在板中进行倍比稀释),分别配制成100 nmol/L,50 nmol/L,25 nmol/L,12.5 nmol/L,6.25 nmol/L,3.12 nmol/L,1.56 nmol/L,样品稀释液直接作为空白孔 0 nmol/L。如配制50 nmol/L标准品:取0.5ml (不要少于0.5ml )100 nmol/L的上述标准品加入含有0.5ml样品稀释液的Eppendorf管中,混匀即可,其余浓度以此类推。
3、 样品稀释液:1×20ml。
4、 检测稀释液A:1×10ml。
5、 检测稀释液B:1×10ml。
6、 检测溶液A:1×120 /瓶(1:100)。临用前以检测稀释液A 1:100稀释(如:10 检测溶液A / 990 检测稀释液A),充分混匀,稀释前根据预先计算好的每次实验所需的总量配制(100 /孔),实际配制时应多配制 0.1-0.2ml。
7、 检测溶液B:1×120 /瓶(1:100)。临用前以检测稀释液B 1:100稀释。稀释方法同检测溶液A。
8、 底物溶液:1×10ml/瓶。
9、 浓洗涤液:1×30ml/瓶,使用时每瓶用蒸馏水稀释25倍。
10、终止液:1×10ml/瓶(2 mol/L H2SO4)。
11、覆膜:5张
12、使用说明书:1份

大鼠甲状腺素抗体(TAb)ELISA Kit

自备物品
1、 酶标仪(建议仪器使用前提前预热)
2、 微量加液器及吸头,EP管
3、 蒸馏水或去离子水,滤纸

大鼠甲状腺素抗体(TAb)ELISA Kit

标本的采集及保存
1、 血清:全血标本请于室温放置2小时或4 过夜后于1000 g离心20分钟,取上清即可检测,或将上清置于-20 或-80 保存,但应避免反复冻融。
2、 血浆:可用EDTA或肝素作为抗凝剂,标本采集后30分钟内于 1000 g离心15分钟,取上清即可检测,或将上清置于-20 或-80 保存,但应避免反复冻融。
3、 其它生物标本:请1000 g离心20分钟,取上清即可检测,或将上清置于-20 或-80 保 存,但应避免反复冻融。

注:以上标本均应密封保存,4 保存应小于1周,-20 不应超过1个月,-80 不应超过2个月;标本溶血会影响最后检测结果,因此溶血标本不宜进行此项检测。

大鼠甲状腺素抗体(TAb)ELISA Kit

操作步骤
实验开始前,各试剂均应平衡至室温,试剂不能直接在37 溶解;试剂或样品配制时,均需充分混匀,混匀时尽量避免起泡。实验前应预测样品含量,如样品浓度过高时,应对样品进行稀释,以使稀释后的样品符合试剂盒的检测范围,计算时再乘以相应的稀释倍数。
1、 加样:分别设空白孔、标准孔、待测样品孔。空白孔加样品稀释液 100 ,余孔分别加标准品或待测样品100 ,注意不要有气泡,加样 时将样品加于酶标板底部,尽量不触及孔壁,轻轻晃动混匀,酶标板加上盖或覆膜,37 温育2小时。为保证实验结果有效
性,每次实验请使用新的标准品溶液。
2、 弃去液体,甩干,不用洗涤。每孔加检测溶液A工作液 100 (临用前配制),酶标板加上覆膜,37 温育1小时。
3、 弃去孔内液体,甩干,洗板 3次,每次浸泡1-2分钟,大约400 /每孔,甩干(也可轻拍将孔内液体拍干)。
4、 每孔加检测溶液B工作液(临用前配制)100 ,加上覆膜,37 温育1小时。
5、 弃去孔内液体,甩干,洗板5次,方法同步骤3。
6、 每孔加底物溶液90 ,酶标板加上覆膜37 避光显色(反应时间控制在15-30分钟,当标准孔的前3-4孔有明显的梯度蓝色,后3-4孔梯度不明显时,即可终止)。
7、 每孔加终止溶液50 ,终止反应,此时蓝色立转黄色。终止液的加入顺序应尽量与底物 液的加入顺序相同。
8、 立即用酶标仪在450nm波长测量各孔的光密度(OD值)。

大鼠甲状腺素抗体(TAb)ELISA Kit

注:
1、 试剂准备:所有试剂在使用前应平衡至室温,使用后请立即按照说明书要求保存试剂。实验操作中请使用一次性的吸头,避免交叉污染。
2、 加样:加样或加试剂时,第一个孔与最后一个孔加样之间的时间间隔如果太大,将会导致不同的 “预温育”时间,从而明显地影响到测量值的准确性及重复性。一次加样时间(包括标准品及所有样品)最好控制在10分钟内。推荐设置复孔进行实验。
3、 温育:为防止样品蒸发,实验时将加上盖或覆膜的酶标板置于湿盒内,以避免液体蒸发;洗板后应尽快进行下步操作,任何时侯都应避免酶标板处于干燥状态;同时应严格遵守给定的温育时间和温度。
4、 洗涤:洗涤过程中反应孔中残留的洗涤液应在滤纸上拍干,勿将滤纸直接放入反应孔中吸水,同时要消除板底残留的液体和手指印,避免影响最后的酶标仪读数。
5、 试剂配制:Detection A及Detection B在使用前请手甩几下或少时离心处理,以使管壁或瓶盖的液体沉积到管底。标准品、检测溶液A工作液、检测溶液B工作液请依据所需的量配制使用,并使用相应的稀释液配制,不能混淆。请精确 配制标准品及工作液,尽量不要微量配制(如吸取检测溶液A时,一次不要小于10 ),以避免由于不准确稀 释而造成浓度误差;请勿重复使用已稀释过的标准品、检测溶液A工作液、检测溶液B工作液。
6、 反应时间的控制:加入底物后请定时观察反应孔的颜色变化(比如,每隔10分钟),如颜色较深,请提前加入终止液终止反应,避免反应过强从而影响酶标仪光密度读数。
7、 底物:底物请避光保存,在储存和温育时避免强光直接照射。

大鼠甲状腺素抗体(TAb)ELISA Kit

洗板方法
1、 手工洗板方法:将推荐的洗涤缓冲液至少0.4ml注入孔内,浸泡1-2分钟,吸去(不可触及板壁)或甩掉酶标板内的液体,在实验台上铺垫几层吸水纸,酶标板朝下用力拍几次;根据需要,重复此过程数次。
2、 自动洗板:如果有自动洗板机,应在熟练使用后再用到正式实验过程中。

大鼠甲状腺素抗体(TAb)ELISA Kit

特异性
本试剂盒可同时检测重组或天然的大鼠TAb,且与其它相关蛋白无交叉反应。

大鼠甲状腺素抗体(TAb)ELISA Kit

计算
各标准品及样本OD值扣除空白孔OD值后作图(七点图),如设置复孔,则应取其平均值计算。以标准品的浓度为纵坐标(对数坐标)OD值为横坐标(对数坐标),在对数坐标纸上绘出标准曲线。推荐使用专业制作曲线软件进行分析,如 curve expert 1.3,根据样品OD值,由标准曲线查出相应的浓度,乘以稀释倍数;或用标准物的浓度与OD值计算出标准曲线的回归方程式,将样品的OD值代入方程式,计算出样品浓度,再乘以稀释倍数,即为样品的实际浓度。

大鼠甲状腺素抗体(TAb)ELISA Kit

说明
1.在储存及孵育过程中避免将试剂暴露在强光中。所有试剂瓶盖须盖紧以防止蒸发和污染,试剂避免受到微生物的污染,因为蛋白水解酶的干扰将导致出现错误的结果。
2. 小心吸取试剂并严格遵守给定的孵育时间和温度。请注意在吸取标本 / 标准品,酶结合物或底物时,第一个孔与最后一个孔加样之间的时间间隔如果太大,将会导致不同的 “预孵育”时间,从而明显地影响到测量值的准确性及重复性。而且,洗涤不充分将影响试验结果。
3. 试剂盒保存:部分试剂保存于-20℃,部分试剂保存于2-8℃,具体以标签上的标示为准。
4. 浓洗涤液会有盐析出,稀释时可在水浴中加温助溶。
5. 刚开启的酶联板孔中可能会含有少许水样物质,此为正常现象,不会对实验结果造成任何影响。
6. 中、英文说明书可能会有不一致之处,请以英文说明书为准。
7. 所有的样品都应管理好,按照规定的程序处理样品和检测装置。

 大鼠甲状腺素抗体(TAb)ELISA Kit

精密度: Intra-assay Precision (Precision within an assay): CV%<8%
Three samples of known concentration were tested twenty times on one plate to assess.
Inter-assay Precision (Precision between assays): CV%<10%
Three samples of known concentration were tested in twenty assays to assess.
 
 大鼠甲状腺素抗体(TAb)ELISA Kit

样本搜集及储存: Serum: Use a serum separator tube (SST) and allow samples to clot for two hours at room temperature or overnight at 4&deg;C before centrifugation for 15 minutes at 1000 &times;g. Remove serum and assay immediately or aliquot and store samples at -20&deg;C or -80&deg;C. Avoid repeated freeze-thaw cycles.
Plasma: Collect plasma using EDTA, or heparin as an anticoagulant. Centrifuge for 15 minutes at 1000 &times;g at 2-8&deg;C within 30 minutes of collection. Assay immediately or aliquot and store samples at -20&deg;C or -80&deg;C. Avoid repeated freeze-thaw cycles.
 
 大鼠甲状腺素抗体(TAb)ELISA Kit

检测步骤: Bring all reagents and samples to room temperature before use. Centrifuge the sample again after thawing before the assay. It is recommended that all samples and standards be assayed in duplicate.
1. Prepare all reagents, working standards, and samples as directed in the previous sections.
2. Refer to the Assay Layout Sheet to determine the number of wells to be used and put any remaining wells and the desiccant back into the pouch and seal the ziploc, store unused wells at 4&deg;C.
3. Add 100&mu;l of standard and sample per well. Cover with the adhesive strip provided. Incubate for 2 hours at 37&deg;C. A plate layout is provided to record standards and samples assayed.
4. Remove the liquid of each well, don't wash.
5. Add 100&mu;l of Biotin-antibody (1x) to each well. Cover with a new adhesive strip. Incubate for 1 hour at 37&deg;C. (Biotin-antibody (1x) may appear cloudy. Warm up to room temperature and mix gently until solution appears uniform.)
6. Aspirate each well and wash, repeating the process two times for a total of three washes. Wash by filling each well with Wash Buffer (200&mu;l) using a squirt bottle, multi-channel pipette, manifold dispenser, or autowasher, and let it stand for 2 minutes, complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining wash Buffer by aspirating ordecanting. Invert the plate and blot it against clean paper towels.
7. Add 100&mu;l of HRP-avidin (1x) to each well. Cover the microtiter plate with a new adhesive strip. Incubate for 1 hour at 37&deg;C.
8. Repeat the aspiration/wash process for five times as in step 6.
9. Add 90&mu;l of TMB Substrate to each well. Incubate for 15-30 minutes at 37&deg;C. Protect from light.
10. Add 50&mu;l of Stop Solution to each well, gently tap the plate to ensure thorough mixing.
11. Determine the optical density of each well within 5 minutes, using a microplate reader set to 450 nm. If wavelength correction is available, set to 540 nm or 570 nm. Subtract readings at 540 nm or 570 nm from the readings at 450 nm. This subtraction will correct for optical imperfections in the plate. Readings made directly at 450 nm without correction may be higher and less accurate.
 
 大鼠甲状腺素抗体(TAb)ELISA Kit

结果计算: Using the professional soft "Curve Expert 1.3" to make a standard curve is recommended, which can be downloaded from our web.
Average the duplicate readings for each standard and sample and subtract the average zero standard optical density.
Create a standard curve by reducing the data using computer software capable of generating a four parameter logistic (4-PL) curve-fit. As an alternative, construct a standard curve by plotting the mean absorbance for each standard on the x-axis against the concentration on the y-axis and draw a best fit curve through the points on the graph. The data may be linearized by plotting the log of the TAb concentrations versus the log of the O.D. and the best fit line can be determined by regression analysis. This procedure will produce an adequate but less precise fit of the data.
If samples have been diluted, the concentration read from the standard curve must be multiplied by the dilution factor.

大鼠甲状腺素抗体(TAb)ELISA Kit

相关产品:

产品名称 英文名称 货号 规格
 人甲状腺素抗体ELISA Kit  Human Thyroxine antibody ELISA Kit  CSB-E08472h  96T 
        
 小鼠抗促甲状腺素受体抗体(TRAb)ELISA Kit  Mouse thyroid stimulating hormone receptor antidoby,TRAb ELISA Kit  CSB-E08471m  96T 
        
 大鼠抗促甲状腺素受体抗体(TRAb)ELISA Kit  Rat thyroid stimulating hormone receptor antidoby,TRAb ELISA Kit  CSB-E08470r  96T 
        
 小鼠甲状腺素抗体(TAb)ELISA Kit  Mouse Thyroxine antibody,TAb ELISA Kit  CSB-E08474m  96T 
        
 大鼠糖原磷酸化酶同工酶MM(GP-MM)ELISA Kit  Rat Glycogen phosphorylase MM,GP-MM ELISA Kit  CSB-E08479r  96T 
        
 人糖原磷酸化酶同工酶MM(GP-MM)ELISA Kit  Human Glycogen phosphorylase MM,GP-MM ELISA Kit  CSB-E08478h  96T 
        
 大鼠糖原磷酸化酶同工酶BB(GP-BB)ELISA Kit  Rat Glycogen phosphorylase BB,GP-BB ELISA Kit  CSB-E08476r  96T 
        
 小鼠糖原磷酸化酶同工酶BB(GP-BB)ELISA Kit  Mouse Glycogen phosphorylase BB,GP-BB ELISA Kit  CSB-E08477m  96T 
        
 人糖原磷酸化酶同工酶BB(GP-BB)ELISA Kit  Human Glycogen phosphorylase BB,GP-BB ELISA Kit  CSB-E08475h  96T

工商信息

企业名称

上海希美化学有限公司

企业信息已认证

企业类型

信用代码

310228001203103

成立日期

2009-05-31

注册资本

10

经营范围

化工原料及产品(除危险化学品、监控化学品、烟花爆竹、民用爆炸物品、易制毒化学品),实验室设备,仪器仪表,金属制品,电子产品,机电产品销售,从事化工科技、计算机科技领域内技术开发、技术咨询、技术服务。【依法须经批准的项目,经相关部门批准后方可开展经营活动】

联系我们
大鼠甲状腺素抗体(TAb)ELISA Kit由上海希美化学有限公司为您提供,货号CSB-E08473r,规格:96T,CAS号:CSB-E08473r,如您想了解更多关于大鼠甲状腺素抗体(TAb)ELISA Kit价格、大鼠甲状腺素抗体(TAb)ELISA Kit结构式、批发、用途等信息,欢迎咨询。除供应大鼠甲状腺素抗体(TAb)ELISA Kit外,还可为您提供人甲状腺素抗体(TAb)ELISA Kit、人甲状腺素抗体ELISA Kit、小鼠甲状腺素抗体(TAb)ELISA Kit等试剂,公司有专业的客户服务团队,是您值得信赖的合作伙伴,上海希美化学客户服务电话,售前、售后均可联系。
推荐产品
供应产品

上海希美化学有限公司

沟通底价

提交后,商家将派代表为您专人服务

获取验证码

{{maxedution}}s后重新发送

获取多家报价,选型效率提升30%
提交留言
点击提交代表您同意 《用户服务协议》 《隐私政策》 且同意关注厂商展位
联系方式:

公司名称: 上海希美化学有限公司

公司地址: 上海市松江区陆家圈路168弄113号 联系人: 李保平 邮编: 201619

主营产品:

仪器信息网APP

展位手机站