人丝氨酸蛋白酶抑制因子肽酶抑制因子进化枝3G(Serpina3g)ELISA Kit

 产品名称： 人丝氨酸蛋白酶抑制因子肽酶抑制因子进化枝3G(Serpina3g)ELISA Kit
 
 英文名称： human serine/cysteine peptidase inhibitor clade A member 3G,Serpina3g ELISA Kit
 
 货号： CSB-E11835h
 
 规格： 96T
 
 种属： human
 
 待测物名称： serine/cysteine peptidase inhibitor clade A member 3G,Serpina3g
 
 缩写： Serpina3g
 
 反应时间： 1-5h
 
 所需样本体积： 50-100ul
 
 检测波长： 450 nm
 
 用途： For research use only. Not for diagnostic use.
 
 精密度： Intra-assay Precision (Precision within an assay): CV%<8%
Three samples of known concentration were tested twenty times on one plate to assess.
Inter-assay Precision (Precision between assays): CV%<10%
Three samples of known concentration were tested in twenty assays to assess.
 
 样本搜集及储存： Serum: Use a serum separator tube (SST) and allow samples to clot for two hours at room temperature or overnight at 4°C before centrifugation for 15 minutes at 1000 ×g. Remove serum and assay immediately or aliquot and store samples at -20°C or -80°C. Avoid repeated freeze-thaw cycles.
Plasma: Collect plasma using EDTA, or heparin as an anticoagulant. Centrifuge for 15 minutes at 1000 ×g at 2-8°C within 30 minutes of collection. Assay immediately or aliquot and store samples at -20°C or -80°C. Avoid repeated freeze-thaw cycles.
 
 检测步骤： Bring all reagents and samples to room temperature before use. Centrifuge the sample again after thawing before the assay. It is recommended that all samples and standards be assayed in duplicate.
1. Prepare all reagents, working standards, and samples as directed in the previous sections.
2. Refer to the Assay Layout Sheet to determine the number of wells to be used and put any remaining wells and the desiccant back into the pouch and seal the ziploc, store unused wells at 4°C.
3. Add 100μl of standard and sample per well. Cover with the adhesive strip provided. Incubate for 2 hours at 37°C. A plate layout is provided to record standards and samples assayed.
4. Remove the liquid of each well, don't wash.
5. Add 100μl of Biotin-antibody (1x) to each well. Cover with a new adhesive strip. Incubate for 1 hour at 37°C. (Biotin-antibody (1x) may appear cloudy. Warm up to room temperature and mix gently until solution appears uniform.)
6. Aspirate each well and wash, repeating the process two times for a total of three washes. Wash by filling each well with Wash Buffer (200μl) using a squirt bottle, multi-channel pipette, manifold dispenser, or autowasher, and let it stand for 2 minutes, complete removal of liquid at each step is essential to good performance. After the last wash, remove any remaining wash Buffer by aspirating ordecanting. Invert the plate and blot it against clean paper towels.
7. Add 100μl of HRP-avidin (1x) to each well. Cover the microtiter plate with a new adhesive strip. Incubate for 1 hour at 37°C.
8. Repeat the aspiration/wash process for five times as in step 6.
9. Add 90μl of TMB Substrate to each well. Incubate for 15-30 minutes at 37°C. Protect from light.
10. Add 50μl of Stop Solution to each well, gently tap the plate to ensure thorough mixing.
11. Determine the optical density of each well within 5 minutes, using a microplate reader set to 450 nm. If wavelength correction is available, set to 540 nm or 570 nm. Subtract readings at 540 nm or 570 nm from the readings at 450 nm. This subtraction will correct for optical imperfections in the plate. Readings made directly at 450 nm without correction may be higher and less accurate.
 
 结果计算： Using the professional soft "Curve Expert 1.3" to make a standard curve is recommended, which can be downloaded from our web.
Average the duplicate readings for each standard and sample and subtract the average zero standard optical density.
Create a standard curve by reducing the data using computer software capable of generating a four parameter logistic (4-PL) curve-fit. As an alternative, construct a standard curve by plotting the mean absorbance for each standard on the x-axis against the concentration on the y-axis and draw a best fit curve through the points on the graph. The data may be linearized by plotting the log of the Serpina3g concentrations versus the log of the O.D. and the best fit line can be determined by regression analysis. This procedure will produce an adequate but less precise fit of the data.
If samples have been diluted, the concentration read from the standard curve must be multiplied by the dilution factor.
   
相关产品：

 
产品名称 英文名称 货号 规格
 人STEAP家族成员1(Steap1)ELISA Kit  human STEAP family member 1,Steap1 ELISA Kit  CSB-E11838h  96T 
        
 人S100钙结合蛋白A9/钙粒蛋白B(S100A9)ELISA Kit  human S100 calcium binding protein A9/calgranulin B,S100A9 ELISA Kit  CSB-E11834h  96T 
        
 人S100钙结合蛋白A8/钙粒蛋白A(S100A8)ELISA Kit  human S100 calcium binding protein A8/calgranulin A,S100A8 ELISA Kit  CSB-E11833h  96T 
        
 人信号传导子及转录激活子2(STAT2)ELISA Kit  human signal transducer and activator of transcription 2,STAT2 ELISA Kit  CSB-E11837h  96T 
        
 人血清淀粉样蛋白A3(SAA3)ELISA Kit  human serum amyloid A3,SAA3 ELISA Kit  CSB-E11836h  96T 
        
 人集蛋白亚家族成员11(COLEC11)ELISA Kit  human collectin sub-family member 11,COLEC11 ELISA Kit  CSB-E11839h  96T