The 1020L Amplifier is a rugged source of RF
power for ultrasonics, induction heating and
laser modulation as well as plasma applications.
It is a totally solid state solution employing RF
DMoS FETs in the power amplification stages,
offering simultaneous forward and reverse
power readouts, and RS232 port for data
collection. The 1020L reflects E&I’s commitment
to reliable and robust RF power.
- 10 KHz – 5 MHz
- Power Measurement
o Forward & Reflected
- Solid State Reliability
- Forced Air Cooling
Class of Operation
Class AB
Frequency Range
10 to 5000 KHz
Rated Power Output
200 Watts
Saturated Power Output
300 Watts
Power Gain
53 dB nominal
Gain Flatness
+/- 1 dB
Input Power for Rated Output
1.0 mW or 0 dBm
Input Impedance
50 ohm
Output Impedance
50 ohm
Ruggedness
Any load VSWR, any phase from open
to Short circuit without damage.
Front Panel Accuracy
+/- 3%
Drive Source Requirements
Any signal Generator, function
Generator or oscillator capable
of up to 0.7 Vpp into 50 ohm
Protection:
INPUT: unit will withstand up to +13dBm input
without damage.
THERMAL: the unit can operate at 45OC
ambient. If the internal temperature becomes
too high the unit will shut down and an error
message will appear on the front panel. The unit
may be re-set by cycling the power or from the
RS232 input.
MISMATCH: the unit will tolerate any mismatch
subject to thermal and current protection.
Accessories Supplied
The unit is supplied with an operations manual
and AC line cord.
Temperature Range
0 – 45O C
Cooling
Forced air.
Weight
45 lbs (16 KG)
Dimensions
5.2 x 16.5 x 18.1 (H x W x D)
The 1020L produces 200 Watts of quasi linear
class AB power over a frequency range of 10
KHz to 5 MHz, with a nominal power gain of 53
dB (+/-1dB). Operation over the entire frequency
range is possible without the need for any
switching.
The front panel display provides simultaneous
measurements of forward and reflected power
as well as the unit’s status. The RS232
connector at the rear of the unit can also be
used to capture this data and reset the unit
should a fault occur.
The E&I 1020L is a 19” rack mount unit 3U high.
It employs an integral power supply capable of
operation at 115 or 220 VAC, 50 – 60 Hz. The
unit weighs approximately 45 lbs or 16 Kg.
企业名称
微纳立方科技(北京)有限公司
企业信息已认证
企业类型
信用代码
110105031497843
成立日期
2021-07-19
注册资本
500
经营范围
技术咨询、技术转让、技术推广、技术服务、技术开发;软件开发;计算机系统服务;数据处理;基础软件服务;应用软件服务(不含医用软件);技术进出口、代理进出口、货物进出口;维修计算机;租赁计算机;销售电子产品、仪器仪表、计算机、软件及辅助设备。(市场主体依法自主选择经营项目,开展经营活动;依法须经批准的项目,经相关部门批准后依批准的内容开展经营活动;不得从事国家和本市产业政策禁止和限制类项目的经营活动。)
微纳立方科技(北京)有限公司
公司地址
朝阳区酒仙桥东路9号A2-西七层
客服电话